Schneider IAP50S handleiding
Handleiding
Je bekijkt pagina 13 van 208
Introduction FOUNDATION Fieldbus Communication
Standard Specifications
Operative Limits
Influence Operative Limits
1
Sensor Body Temperature
2
PVDF inserts -7 and +82°C (+20 and 180°F)
Silicone fill fluid -46 and +121°C (-50 and +250°F)
3 4
Fluorinert fill fluid -29 and +121°C (-20 and +250°F)
5
NEOBEE
®
fill fluid -18 and +121°C (0 and 250°F)
Electronics Temperature
Without LCD -40 and +85°C (-40 and +185°F)
6 7
With LCD -40 and +85°C (-40 and +185°F)
6 7 8
Relative Humidity 0 and 100%
9
Supply Voltage 9 V dc and 32 V dc
Mounting Position No limit
Vibration
Aluminum Housing Per IEC 60770 for “field with high vibration level or pipeline with high vibration
level”: 0.42 mm peak-to-peak displacement from 10 to 60 Hz, 3 “g” constant
acceleration input over a frequency range of 60 to 1000 Hz
Stainless Steel Housing Per IEC 60770 for “field with general application or pipeline with low vibration
level”: 0.3 mm peak-to-peak displacement from 10 to 60 Hz, 2 “g” constant
acceleration input over a frequency range of 60 to 1000 Hz
Span and Range Limits
Limits for Direct Connect Transmitters
Table 1 - Span Limits for Direct Connect Transmitters
Code
Span Limits
10
D
3.4 and 1380 kPa (0.5 and 200 psi)
E
0.034 and 13.8 MPa (5 and 2000 psi)
F
0.52 and 41.4 MPa (75 and 6000 psi)
11
MI 020-612 13
1. Normal Operating Conditions and Operative Limits are defined per ANSI/ISA 51.1-1979 (R1993)
2. Refer to MI 020-369 for temperature limits with pressure seals.
3. Selection of Option -J extends the low temperature operative limit of transmitters with silicone filled sensors down to -50°C (-58°F).
Performance is not assured below -29°C. Sensor damage may occur if process is frozen. Contact Global Customer Support for availability of
this option.
4. -46 and +50°C (-50 and +122°F) for biplanar AP transmitters.
5. -18°C (0°F) for J range (IGP05S transmitters only).
6. -40 and +75°C (-40 and +167°F) for transmitters with ATEX flameproof classification.
7. -40 and +50°C (-40 and +122°F) for biplanar AP transmitters.
8. Display updates are slowed and readability is decreased at temperatures less than -20°C (-4°F).
9. Relative humidity refers to transmitters with housing covers installed and conduit entrances sealed. To maintain IEC IP66/IP67 and NEMA
Type 4X protection, plug the unused conduit opening with the metal plug provided. Use a suitable thread sealant on both conduit connections.
In addition, the threaded housing covers must be installed. Turn covers to seat the o-ring into the housing, then continue to hand-tighten until
the cover contacts the housing metal-to-metal.
10. Values listed are in absolute or gauge pressure units, as applicable.
11. Available for gauge pressure transmitters only.
Bekijk gratis de handleiding van Schneider IAP50S, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Schneider |
| Model | IAP50S |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 25829 MB |
