Roland MC-101 handleiding

Handleiding

123456789101112131415161718192021/ 21

Afdrukken

Je bekijkt pagina 3 van 21

MC-101 Update – Functions Added in Ver.1.80

33

Parameter Value Explanation

T1A

(T1 ATTACK)

0–1023

Species the time over which the initial

value changes to the maximum value after

the note starts.

T3D

(T3 DECAY)

0–1023

Species the time over which the SUSTAIN

value is reached following the ATTACK.

L3S

(L3 SUSTAIN)

-511–+511

Species the sustain value of the pitch

envelope.

ENV COM

(ENV Common)

Parameter Value Explanation

ADS

(ADSR MODE)

The envelope works in simple A-D-S-R mode.

LFO 1/2

Here you can make LFO settings.

Parameter Value Explanation

WAV

(WAVE TYPE)

These buttons set the LFO waveform.

SIN Sine wave

TRI Triangle wave

SAW-UP Sawtooth wave

SAW-DW Sawtooth wave (negative polarity)

SQR Square wave

RND Random wave

TRP Trapezoidal wave

S&H

Sample and Hold wave (changes the LFO

value once every cycle)

CHS Chaos wave.

VSIN

Modied sine wave. The amplitude of the

sine wave is randomly varied once every

cycle.

STEP

A waveform generated from data specied

by LFO Step 1–16.

This produces a xed pattern of stepped

change like a step modulator.

* The MC-101 does not support step modulator

editing.

RAT

(RATE or RATE NOTE)

0–1023

(RATE)

This is eective if SYNC TEMPO is OFF.

Species the LFO rate without regard to the

tempo. Higher values produce a faster LFO

rate (a shorter cycle).

1/64T–4

(RATE NOTE)

This is eective if SYNC TEMPO is ON.

Sets the LFO cycle as a note length.

FLT

(FILTER DEPTH)

-100–+100

Species how deeply the LFO will aect the

cuto frequency.

PIT

(PITCH DEPTH)

-100–+100

Species how deeply the LFO will aect

pitch.

* If OSC TYPE is other than VA, the range is

limited to -63–+63.

FAD

(FADE IN)

0–1023

Species the time over which the LFO

amplitude will reach the maximum

(minimum).

SYN

(SYNC TEMPO)

OFF, ON

Set this ON if you want the LFO rate to

synchronize with the tempo.

AMP

(AMP DEPTH)

-100–+100

Species how deeply the LFO will aect the

volume.

PAN

(PAN DEPTH)

-63–+63

Species how deeply the LFO will aect the

pan.

EQ

Here you can make equalizer settings.

Parameter Value Explanation

SW

(EQ SWITCH)

OFF, ON Turns the equalizer on/o.

LO

(LO GAIN)

-24–+24 [dB] Sets the gain of the low frequency range.

Parameter Value Explanation

MID

(MID GAIN)

-24–+24 [dB] Sets the gain of the mid frequency range.

HI

(HI GAIN)

-24–+24 [dB] Sets the gain of the high frequency range.

Q

(MID Q)

0.5–16.0

Bandwidth of the mid frequency range.

Set a higher value for Q to narrow the range

to be aected.

LO

(LO FREQ)

20–16000 [Hz] Sets the frequency of the low range.

MID

(MID FREQ)

20–16000 [Hz] Sets the frequency of the middle range.

HI

(HI FREQ)

20–16000 [Hz] Sets the frequency of the high range.

MATRIX 1–4

Here you can connect various parameters as if you were patching

them.

You can connect up to four parameters.

Parameter Value Explanation

SRC

For an explanation

of each

parameter, refer

to the “Reference

Manual” (p.45)

“Parameter List”.

Species the control-source signal.

* If you specify SycCtrl 1–4, you can use the

panel [FILTER] [MOD] [FX] knobs to control the

parameters.

TO

Species the parameter that is controlled.

Ø

For an explanation of each parameter,

refer to the “Reference Manual” (p.45)

“Parameter List”.

DEP

(DEPTH)

-63–+63

Species the amount (depth) by which the

parameter is varied.

VELOCITY SENS

Parameter Value Explanation

LVL

(LEVEL VELOCITY)

-100–+100

Set this when you want the volume of the

partial to change depending on the force

with which you press the keys.

Set this to a positive (+) value to have the

changes in partial volume increase the more

forcefully the keys are played; to make the

partial play more softly as you play harder,

set this to a negative (-) value.

CUT

(CUTOFF VELOCITY)

-100–+100

Use this parameter when changing the

cuto frequency to be applied as a result of

changes in playing velocity.

Specify a positive “+” value if you want the

cuto frequency to raise when you play

strongly, or a negative “-” value if you want it

to lower.

DEP

(FILTER DEP VELO)

-100–+100

Specify this if you want keyboard playing

dynamics to aect the lter envelope depth.

Specify a positive “+” value if you want the

lter envelope to apply more deeply as you

play more strongly, or a negative “-” value if

you want it to apply less deeply.

T4R

(FENV T4R VELO)

-100–+100

Specify this if you want key release velocity

to aect Time 4 of the lter envelope.

If you want Time 4 to be speeded up for

quickly released notes, set this parameter

to a positive (+) value. If you want it to be

slowed down, set this to a negative (-) value.

123456789101112131415161718192021/ 21

Bekijk gratis de handleiding van Roland MC-101, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.

Productinformatie

Caratteristiche Prodotto

Gerelateerde producten van Roland (Niet gecategoriseerd)

Handleiding bekijken

Roland DV-7DLC

Niet gecategoriseerd - handleiding

Handleiding bekijken

Roland SO-DA4

Niet gecategoriseerd - handleiding

Handleiding bekijken

Roland SR-JV80-09

Niet gecategoriseerd - handleiding

Handleiding bekijken

Roland DV-7DL PRO

Niet gecategoriseerd - handleiding

Handleiding bekijken

Roland Fantom-X Audio Track Expansion Kit

Niet gecategoriseerd - handleiding

Handleiding bekijken

Roland MC-707

Niet gecategoriseerd - handleiding

Handleiding bekijken

Roland System-500 531

Niet gecategoriseerd - handleiding

Handleiding bekijken

Roland JUNO-60 Chorus

Niet gecategoriseerd - handleiding

Andere merken in Niet gecategoriseerd