JANDY JAOPX200 handleiding
Handleiding
Je bekijkt pagina 7 van 60
Page 7
Jandy
®
X Series
™
AOP System | Installation & Operation Manual ENGLISH
4. Loosen or remove the tubing clamp on the
injector tube adapter end of the ozone gas line.
Use pliers (if necessary) to twist and unlock the
clamp.
5. Pull the tubing from injector tube adapter, then
unthread the adapter from the injector manifold.
6. Apply Teflon
™
based thread sealant and install
the injector cap into the injector manifold.
7.
Turn on pool circulation system and run at
highest normal operating pressure.
8. Check for leaks outside and inside of the Jandy
AOP system. Correct any leaks outside of the
system. Contact Customer Service for any
internal leaks.
9.
Once the pressure test is complete, turn off the
pool circulation system.
10. Remove the injector cap. Re-thread the injector
tube adapter into the injector manifold.
11. Push the free end of the tubing into the injector
tube adapter.
12. Secure the tubing clamp on the injector tube
adapter end of the ozone gas line. Use pliers (if
necessary) to twist and lock the clamp.
13. Use a flat blade screwdriver to turn the door
latches counter clockwise and close the door.
14. Turn on water and power at their sources.
3.5.5 Leak Test
Turn on pool circulation system and run at the
highest normal operating pressure. Check for leaks
outside and inside of the Jandy AOP system. Correct
any leaks outside of the system. If any leaks are
found inside the Jandy AOP, contact Customer
Service.
3.6 Electrical
3.6.1 Main Power
Connect the
Jandy AOP system
to the pool timing
clock so it operates simultaneously with the pool
pump. The
Jandy AOP
system has an access hole
for a 1/2" conduit fitting. Install fitting (not provided)
and run wire to terminal block inside unit. Remove the
cover (refer to Ozone Module Servicing) and locate
the terminal block (refer to Figure 5) on the left side
of the enclosure. Connect Line 1, Line 2, and ground
to the terminal block as indicated by the label on the
generator bracket. Refer to the IMPORTANT SAFETY
INSTRUCTIONS at the beginning of this manual for
important wiring information.
3.6.2 Bonding and Grounding
CAUTION
This AOP system must be connected to a bonding grid with a solid
copper wire not smaller in diameter than 8 AWG (In Canada, it shall be
no smaller than 6 AWG.)
The National Electrical Code
®
(NEC
®
in the United
States) or the Canadian Electrical Code (CEC in
Canada) requires pool equipment to be bonded to
each other. Check your local codes to determine if the
NEC or CEC and/or other local installation codes are
enforced by the Authority Having Jurisdiction (AHJ in
the United States) or the local competent authorities
in Canada. A solid, copper 8.37 mm² (8 AWG) wire
is required per the NEC, and 13.3 mm² (6AWG) per
the CEC, for bonding the equipment to a permanent
bonding connection that is acceptable to the local
AHJ or the local competent authorities in Canada.
Refer to your locally enforced codes for the
acceptable bonding wire gauge. Connect to the
bonding point located on the bottom of the AOP
system to a common bonding point. Do not use
theAOP system as the common bonding point.
Eachpiece of non-related pool equipment requiring
a ground should also be bonded to the common,
approved bonding point.
National Electrical Code
®
(NEC
®
) requires bonding
of the Pool Water. Where none of the bonded
pool equipment, structures, or parts are in direct
connection with the pool water; the pool water shall
be in direct contact with an approved corrosion-
resistant conductive surface that exposes not less
than 5800 mm² (9 in²) of the surface area to the pool
water at all times. The conductive surface shall be
located where it is not exposed to physical damage
or dislodgement during usual pool activities, and
it shall be bonded in accordance with the bonding
requirements of NEC Article 680. Refer to locally
enforced codes for any additional pool and spa
bonding requirements.
Bekijk gratis de handleiding van JANDY JAOPX200, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | JANDY |
| Model | JAOPX200 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 7868 MB |
