Zodiac HPO handleiding
Handleiding
Je bekijkt pagina 18 van 28
17
3.2.2 User maintenance
• Make sure that the venlaon grid is not blocked by any foreign bodies.
• Clean the evaporator (for locaon see § “5.3 I Dimensions and marking”) using a so brush and a fresh water spray
(disconnect the power cable); do not fold over the metal wings, then clean the condensate drainage line to remove
any impuries that may be blocking it.
• Do not use a high pressure jet. Do not spray with rain water, salt water or water which is full of minerals.
• Clean the outside of the appliance using a solvent-free product; a specic "PAC NET" cleaning kit is available as an
accessory in the Zodiac® catalogue for this purpose (see § “5.1 I Descripon”).
3.2.3 Maintenance to be carried out by a qualied technician
• Read the safety instrucons carefully before carrying out any of the maintenance operaons
described below, see "3.2.1 Safety instrucons".
• Check that the control system is operang correctly.
• Check that the condensates ow correctly when the appliance is in operaon.
• Check the safety mechanisms.
• Check the connecon of the metal masses to the earth.
• Check that the electrical cables are correctly ghtened and connected and that the switch box is clean.
❹ Troubleshoong
• Before you contact the retailer, carry out these few simple checks using the following tables
if a problem occurs.
• If the problem is not resolved, contact your retailer.
• : Acons to be performed by a qualied technician only.
4.1 I Appliance behaviour
The appliance
does not start
heang straight
away
• When the temperature setpoint is reached, the heat pump stops heang: the water temperature
is higher than or equal to the temperature setpoint.
• When the water ow rate is zero or is not enough, the heat pump stops: check that the water
is circulang correctly in the heat pump (see § “2.2 I User interface presentaon”) and that the
hydraulic connecons are correct.
• The outdoor temperature is outside the heat pump's operang range.
• It may be that the heat pump has detected an operang fault (see § “4.2 I Error code display”).
• If you have checked these points and the problem persists: contact your retailer.
The appliance
is discharging
water
• Oen called condensates, this water is the moisture contained in the air which condenses on
contact with certain cold mechanisms in the heat pump, especially on the evaporator. The
damper the air, the more condensates your heat pump will produce (your appliance may drain
several litres of water per day). This water is recovered at the base of the heat pump and drained
by the condensate drainage elbow (see § “1.2 I Hydraulic connecons”).
• To check that the water is not coming from a leak in the pool circuit on the heat pump, shut
down the heat pump and run the lter pump to circulate water in the heat pump. If the water
connues to ow through the condensate drainage lines, there is a water leak in the heat pump:
contact your retailer.
The evaporator is
iced over
• Your heat pump will soon switch to its defrost cycle to melt the ice.
• If your heat pump cannot manage to defrost its evaporator, it will stop itself; this means that the
outdoor temperature is lower than the minimum operang temperature.
The appliance is
"smoking"
• The machine has come to the end of the defrost cycle; water has changed to gaseous state and
passes through the grid.
• If your heat pump is not in its defrost cycle, this is not normal. Switch o and disconnect the
heat pump immediately and contact your retailer.
The appliance is
not working
• If there is no display, check the power voltage and the fuses.
• When the temperature setpoint is reached, the heat pump stops heang: the water temperature
is higher than or equal to the temperature setpoint.
• When the water ow rate is zero or is not enough, the heat pump stops: check that the water is
circulang correctly in the heat pump (see § “2.2 I User interface presentaon”).
• The outdoor temperature is outside the heat pump's operang range.
• It may be that the heat pump has detected an operang fault (see § “4.2 I Error code display”).
Bekijk gratis de handleiding van Zodiac HPO, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Zodiac |
| Model | HPO |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 6991 MB |
