Zodiac CAE Ducted handleiding
Handleiding
Je bekijkt pagina 14 van 26
H03846‐00.A1.EN–2012/10 13
3.5.2Hotwaterbattery
Supply the battery with hot water at 50 °C minimum from the heat source (boiler, heat pump, geothermal
energy,solarheating),installationmustbecarriedoutbyaqualifiedtechnician,usingacirculator(notsupplied)
whichwillbepoweredbyterminalsC‐Contheelectricalterminalboard.
Insulate the hot water battery hot water pipes between the heat source and the appliance (for the
purposeoflimitingcalorieloss).
connectiontoaZPCEdoublecircuitgasboiler:connecttheterminals3‐6oftheterminalboard,toterminals3‐6
oftheboilerterminalboard,
Terminals3‐6canalsoensureaheatsourcecontrolfunction(see§2.6.2).
adjust thethermostat between to 26 and 28°C (maximum 30°C), in general set the air temperature 1 to 2°C
higherthanthepoolwatertemperature,
If your pool has a cover (shutter or bubble sheet type, etc.), you can lower the room temperature (by
adjusting the thermostat to about 20°C) when it is in place andraise the pool hall temperature before
removingthecover.
apost‐ventilationrunsfor3minuteswhenthereferencetemperatureisreducedonthether mostatlocatedin
thepoolhall(withthe“VI/VP”switchon“VI”,withoutanydehumidificationordefrostingcyclesinprogress):
checkthatthecirculatorstops.
Warning‐lowtemperature:ifthedeh umidifierhotwaterbatteryisnotsuppliedbyaboiler,butbyan
aero‐thermal ora geothermalsystem, theheatingcircuitwater willbeat amaximum temperature of
50‐40°C.Thepowerofthebatterywillthenbeconsiderablylower(3to4timesless)thanthenominal
power given for water at90‐70°C. If the power of the battery islower than the heating needs of the
room,planforadditionalheatingbyradiator,heatedfloororfanconvector.
3.5.3Titaniumwatercondenser
connecttheintakeandoutputtothefilterusingaby‐pass,accordingtothemarkings
ontheappliance(beforethepoolwatertreatmentsystem),see§2.7.2,
Adjustingtheby‐passforthewatercondenser:
- openvalvehalfway
- openvalvesandcompletely
plan to shunt th
e filter clock from the S‐S terminals on the appliance electrical
terminalboard,
inthecaseofa hydraulicconnectionwithpumpthatisindependentofthefiltering
system, plan to power this pump using theP‐P terminals ontheappliance terminal board(maximum power:
60Wwith230VAC,otherwiserelaythepowersupplyfromanextraele
ctriccontactor),
startingup:setthe“TH”digitaldisplaythermostatfittedinsidetheelectricalbox:
press “SET” to display the current reference value (factory preset at 27°C, thus the
thermostatoutputwillbeactivatedwhenthepoolroomtempera
turewillrisesabove29°C
anddeactivatedifthetemperaturedropsbelow27°C):the“out1”LEDblinks(hysteresis=
2°C),
- press or(possiblerangevalues:25°Cminimumand45°Cmaximum),
- press“SET”,ordonotoperatefor15seconds,toconfirm.
checkthatthefilterpu
mpstartswhentheadjustmentofthisdigitaldisplaythermostatis
reducedtobelowthesurroundingtemperature.
checkthatthe«VCA»indicatorlightswhenthethermostatreferencevalueislowered.Bydefault,checkthat
thefilterpumpisoperationalandsufficientlyirrigatesthewater condenser(seeby‐pass adjustment).
when the wat
er condenser option is operational (VCA indicator on), check that the «EV» solenoid valve is
poweredfromterminalsEandV(230Vac)ontheapplianceterminalboard.Ifthisis notthecaseadjusttheby‐
pass so that there is a sufficient flow of water in the cond
enser to activate the flow controller fitted at the
output of the water con denser (this safety device is connected between terminals I and D, see the electric
wiringdiagramintheappendix).
Bekijk gratis de handleiding van Zodiac CAE Ducted, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Zodiac |
| Model | CAE Ducted |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 6812 MB |
