Zipper ZI-BSF1500 handleiding
Handleiding
Je bekijkt pagina 32 van 39
CLEANING, MAINTENANCE, STORAGE, DISPOSAL
ZIPPER MASCHINEN GmbH www.Zipper-Maschinen.at 32
ZI-BSF1500
• Loosen the screws (1) from the cutting tooth (2) to remove it
from the milling head
• Unscrew the lock nut (3).
• Remove the cutting insert (4), replace it with a new one, and
screw it back on.
• Then screw the cutting tooth back onto the milling head
NOTE: Tightening torque is 86 NM
16.2.7 Clean / replace the air filter
NOTE
A dirty air filter can contribute to problems starting the machine, loss of power during
operation and shorten engine life.
Zipper Maschinen accepts no liability for engine damage resulting from
failure to regularly clean the air filter.
• To clean the air filter, first loosen the wing nut on the air filter housing,
remove the cover (foam filter element (2)) and remove the air filter
cassette (paper filter element (1)). Clean both elements mechanically
with a soft brush.
• If only the air filter cassette is to be cleaned, blow a dry jet of
compressed air from the inside against the filter until all dust has been
removed.
An air filter change is necessary when:
- The engine power drops and the fuel consumption increases at the
same time,
- the oil consumption increases,
- the starting of the engine becomes more difficult.
16.2.8 Clean / replace the spark plug
1. Pull out the spark plug cap and remove impurities from the outside of the spark plug.
2. Unscrew the spark plug using the spark plug wrench.
3. Check the ceramic insulation, clean the electrodes (metal tips) and check the distance
between the contacts. It should be 0.7 to 0.8 mm.
4. Reinstall the cleaned (or replaced) spark plug and replace the spark plug cap.
16.2.9 Adjust the stop switch
The stop switch must be set as follows after a change:
• Loosen the hexagon nut (3).
• For the correct distance, hold the safety bar (2) and the
handle (1) together and lower the rod (4) onto the switch
button (5) until it can no longer be pressed.
• Turn the rod
- clockwise to lower it,
- anti-clockwise to raise.
• Then raise the rod (4) by one turn (anticlockwise).
• Tighten the hexagon nut (3).
• Check the setting by releasing the safety bar (2). A “click”
sound indicates correct adjustment.
16.2.10 Checking / adjusting the brake system
Check
• Pull the brake (1) and push the handlebar down (2) so
that the milling tool is lifted off the ground.
NOTE: The tyres must be locked in this position. If a tyre
rotates, adjust the brake as follows at the brake lever (3).
Adjust
• Remove the adjusting screw (4).
• Turn the rotary knob (5)
- clockwise to increase the tension,
- counterclockwise to reduce the tension.
• Fix this position with the adjusting screw (4).
16.3 Storage
Store the cleaned machine in a dry, frost-proof, well-ventilated and lockable place when not in use.
Make sure the storage location is away from heat sources, flames and sparks. Make sure that
unauthorised persons and especially children do not have access to the machine.
2
1
4
3
2
1
3
4
5
Bekijk gratis de handleiding van Zipper ZI-BSF1500, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Zipper |
| Model | ZI-BSF1500 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 9827 MB |
