Whirlpool WDT550SAPZ handleiding
Handleiding
Je bekijkt pagina 11 van 64
11
Drain Requirements
� A new drain hose is supplied with your dishwasher. If drain
hose is not long enough, use a drain hose extension with a
maximum length of 12 ft (3.7 m).
� Make sure to connect drain hose to waste tee or disposer inlet
above drain trap in house plumbing and 20" (508 mm)
minimum above the floor. It is recommended that the drain
hose either be looped up and securely fastened to the
underside of the counter or be connected to an air gap.
IMPORTANT: This product is not equipped with a high loop on the
side of the dishwasher. The installer is responsible for adding a
high loop in the adjacent cabinet. A high loop is required if the
dishwasher will drain into a floor drain. This prevents water draw
off from the dishwasher during operation. When the drain is
connected to a sink drain, counter-top air-gap or disposer, the
high loop is generally not required. An check valve internal to the
drain prevents back-flow into the dishwasher.
� Make sure to use an air gap if the drain hose is connected to
house plumbing lower than 20" (508 mm) above subfloor or
floor.
A
A. Air gap
� If required, the air gap should be installed in accordance with
the air gap installation instructions. When you are connecting
the air gap, a rubber hose (not provided) will be needed to
connect to the waste tee or disposer inlet.
� Use 1/2" (12.7 mm) minimum I.D. drain line fittings.
Water Supply Requirements
� This dishwasher maybe fitted with a smart inlet hose with a
water cut off valve. Do not cut the water inlet hose for any
reason, to install, adapt or shorten.
� This dishwasher has a water heating feature and also requires
a connection to a hot water supply line.
� A hot water line with 20 psi to 120 psi (138 kPa to 827 kPa)
water pressure can be verified by a licensed plumber.
� 120°F (49°C) water at dishwasher
� 3/8" (9.5 mm) O.D. tubing with compression fitting or flexible
braided or non braided water supply line.
� Included water inlet hose with Leak Detection System for some
models.
� Included 3/8" (9.5 mm) Compression x 3/4" (19 mm) Water
inlet adapter (only for models with Leak Detection System).
� If installed in new construction, make sure the house water
supply lines have been flushed prior to connecting the
dishwasher to remove any debris that may exist in the supply
line.
Electrical Requirements
Be sure that the electrical connection and wire size are adequate
and in conformance with the National Electrical Code,
ANSI/NFPA 70 - latest edition, and all local codes and ordinances.
For a fee, a copy of the above code standards can be obtained
from:
National Fire Protection Association
1 Batterymarch Park
Quincy, MA 02169-7471
You Must Have:
� 120 V, 60 Hz, AC-only, 15 A or 20 A, fused electrical supply.
� Copper wire only.
� A maximum of 2 field wiring supply conductors (12 AWG
largest size) plus 1 grounding conductor are permitted in the
terminal box.
� An included junction box for electrical connection.
We Recommend:
� Install the dishwasher on a circuit with appropriate interrupter
per your local code. The dishwasher is compatible with time
delay fuses, standard circuit breakers, and GFCI and AFCI
circuit breakers.
Circuit Requirement:
� The dishwasher may be installed on the same circuit as a
garbage disposal providing that the branch circuit cannot
exceed rated circuit load and must comply with all governing
codes and regulations such as but not limited to National
Electrical Code, ANSI/NFPA 70 - latest edition.
� No electrical connections other than the dishwasher power
and ground connections can be made inside of the dishwasher
junction box.
If Connecting Dishwasher with a Power Cord:
� Use a UL-listed power cord kit
marked for use with dishwasher. See
the “Tools and Parts” section for part
details.
� Plug into a grounded 3-prong outlet.
Outlet must meet all local codes and
ordinances.
If Connecting Dishwasher with Direct Wiring:
� Use flexible, armored, or nonmetallic
sheathed copper wire with grounding
wire that meets the wiring
requirements for your home and
local codes and ordinances.
� Use only the supplied plastic cable fittings for flexible and
non-metallic sheathed wiring (Romex, etc.). Do not use
metallic strain reliefs for these wire constructions.
� Use a UL-listed/CSA-approved metallic strain relief for
armored cable installations (21 mm diameter) if using armored
cable. Install the strain relief per the strain relief
manufacturer’s installation instructions.
� Use a UL-listed/CSA-approved metallic strain relief for flexible
metal conduit installations if using flexible metal conduit. Install
the strain relief per the strain relief manufacturer’s installation
instructions.
Bekijk gratis de handleiding van Whirlpool WDT550SAPZ, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Whirlpool |
| Model | WDT550SAPZ |
| Categorie | Wasmachine |
| Taal | Nederlands |
| Grootte | 11080 MB |
