VOREL 73403 handleiding
Handleiding
Je bekijkt pagina 7 van 28
7
EN
ORIGINAL INSTRUCTIONS
OPERATION OF THE TOOL
Installation of a gas cartridge
Installation of a gas cartridge should be realised outdoors or
in a well-ventilated room, far from sources of fi re or excessive
heat. Maintain a safe distance from bystanders.
If there is a gas cartridge in the soldering lamp, then make sure
it is empty. Shake the gas cartridge, and if you can hear the so-
und of a liquid then there is gas in the cartridge. In such cases
it is prohibited to remove the gas cartridge.
Close the gas valve, turning the handwheel of the regulator to
the limit towards the symbol „-”.
Make sure the needle and the sealing around it are not da-
maged or worn out. A correct needle and sealing is shown in
Illustration (III). In case you detect any sign indicating they are
damaged or worn out, for example those presented in Illustra-
tion (IV), then it is prohibited to install a gas cartridge.
In the case of the 73400 blowtorch, unscrew the mounting nut
(V), insert the gas canister into the lamp basket and press until
the canister membrane is pierced. Once the container’s mem-
brane is punctured, gas will fl ow out of the container; from this
point on, the container should not be disassembled until it is
completely empty. Then secure the container against slipping
out of the basket by tightening the mounting nut.
For the 73403 blowtorch, pull out the wire spacer (VI). Then
unscrew the gas container basket from the blowtorch, slide the
gas container into the lamp basket, secure the gas container
against slipping out of the basket with a wire spacer. Screw
the blowtorch onto the basket with the gas canister properly
installed. While tightening, the container’s membrane will be
punctured and gas will fl ow out of it. From that moment on,
the container should not be disassembled until it is completely
empty.
Attention! It is prohibited to operate the soldering lamp without
a correctly installed gas cartridge, which is, for example, incor-
rectly protected in the basket.
Make sure there is no gas leakage, using water with soap. In
case bubbles are formed then there is leakage. It is prohibited
to work with a tool in which gas leakage has been detected.
Work with a soldering lamp
Make sure there is no gas leakage, and then slightly turn the
handwheel of the regulator towards the symbol „+”. Light the
gas at the outlet of the burner. In case of the lamp 73400 use
the external lighter (VII), and in case of the lamp 73403 you
may use the internal lighter, pressing the button (VIII). Using the
handwheel of the regulator adjust the fl ame so that the fl ame
is blue. Avoid orange fl ames. Before you proceed to work, wait
for approximately one minute, observing all the time if there is
any sign of undesirable functioning. During the initial stage of
heating up there might be some fl ickering of gas. At that stage
the gas cartridge is in an upright position. If the fl ickering does
not stop automatically, then it is necessary to turn the fl ame off
and contact the manufacturer.
Attention! During work do not incline the lamp more than neces-
sary. The gas cartridge should not be inclined by more than 45
grades towards any direction.
Attention! Do not put a burning burner down. Do not heat up
the gas cartridge.
Turning the lamp burner off
Turn the handwheel of the regulator to the limit towards the
symbol „-”. The fl ame will go out automatically. Be careful, since
the metal parts of the burner heated up during work. Put the
lamp down and wait until it has cooled down.
Attention! It is prohibited to cool the lamp down with water.
Maintenance of the tool
Clean the tool with a soft, humid cloth. Heavy dirt should be
removed with water and soap. Do not use abrasive cleaning
agents.
In case of any damage or dirt in the nozzle contact a service
point of the manufacturer. It is prohibited to clean the nozzle
alone, particularly using sharp objects.
Do not modify the tool. Do not use a tool with damaged ele-
ments.
Storage
The tool must be stored in the provided individual cases in a
dark, dry and well ventilated room, protected from any access
of unauthorised persons, particularly children. The tool must be
stored in an upright position.
Bekijk gratis de handleiding van VOREL 73403, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | VOREL |
| Model | 73403 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 4334 MB |
