VOREL 73403 handleiding
Handleiding
Je bekijkt pagina 6 van 28
6
EN
ORIGINAL INSTRUCTIONS
PROPERTIES OF THE PRODUCT
The gas soldering lamp has been designed for soldering, he-
ating or drying. Since it is fed with butane cartridges (or optio-
nally with propane and butane cartridges), it is possible to ope-
rate the tool where there is no source of electric energy. The
tool may be used only with 190 g disposable cartridges, con-
taining technological mixture of propane and butane, equipped
with a perforable membrane. The gas cartridges must comply
with EN 417. The tool has been designed solely for domestic
use and must not be used professionally, i.e. in plants or for
commercial purpose. A correct, reliable and safe operation of
the tool depends on its correct use, so:
Important: Read the operating manual thoroughly in order
to get acquainted with the tool before it is connected to the
gas cartridge. Keep the manual for future reference.
The supplier shall not be held responsible for any damage oc-
curred as a result of failure to observe safety regulations and
indications contained in this manual.
ACCESSORIES
The tool is delivered complete and does not require assembly.
Gas cartridges not included.
TECHNICAL PARAMETERS
Parameter
Unit of meas-
urement
Value
Catalogue number - 73400 73403
Types of gas - butane butane
Kind of gas cartridges -
190 g (EN 417) under direct
pressure
Flame temperature [
O
C] 1200 1200
Nominal fl ux [g/h] 123 123
Heat load [kW] 1,7 1,7
Weight (without gas cartridge) [kg] 0,4 0,5
SAFETY RECOMMENDATIONS
The tool may be used only with 190 g disposable gas cartrid-
ges, which contain technological mixture of propane and bu-
tane, equipped with perforable membrane. The gas cartridges
must comply with EN 417. An attempt to install other types of
gas cartridges may imply a danger.
Do not ever install gas cartridges without having previously
read the instructions printed on them.
The original structure and settings must not be modifi ed. An
attempt to modify the settings or the structure of the unit and
remove certain elements or using them for other purposes than
intended may be dangerous.
Make sure the sealing (between tool and the gas cartridge) are
in place and in good conditions, before you install a gas cartrid-
ge. Do not use the tool, if the sealing are damaged or worn out.
Do not use the tool, if it is not tight, damaged or if it does not
function correctly. Do not use the tool with any defect.
Close the valves of the unit before connection. Do not smoke
while changing gas cartridges.
The tool must be operated in well ventilated areas, in accordan-
ce with national regulations regarding: supply of air for burning;
avoidance of dangerous gathering on unburnt gases.
The tool should be used far from infl ammable materials. Keep a
minimum distance of 5 metres between the outlet of the burner
and the nearby surfaces (walls, ceilings). Do not ever direct the
outlet of the burner towards people or animals.
Gas cartridges should be replaced in well ventilated places,
preferably outdoors, far from any sources of fi re, such as open
fl ames, pilot burners, electric heaters and away from other pe-
ople.
If the tool is not tight (you can smell gas), then remove it imme-
diately outdoors to a well-ventilated place containing no source
of fi re, where the leakage may be localized and eliminated. If
you want to check any leakage of the tool, do it outdoors. Do
not try to detect leakage using fl ames. To do so use water with
soap.
During work the outlets of the burners heat up to a high tempe-
rature. Keep children and bystanders away from the tool.
Before replacement make sure the gas cartridge is empty, and
shake it to hear a sound of liquid. In case of perforated gas
cartridges do not ever replace them before you make sure they
are completely empty.
Before you install a new gas cartridge, make sure the burners
are turned off . Before you install a new gas cartridge in the tool,
check the sealing. Replace gas cartridges outdoors and away
from other people.
Do not modify the tool.
In case the tool must be sent to the manufacturer or a service
point, it is required to cool it down, disconnect the gas cartridge
and then pack the tool in an individual paper package adequ-
ately for the given means of transport. It is prohibited to send
the tool along with a gas cartridge. Transport of dangerous
materials is subject to restrictions.
Do not put a burning burner down. Do not heat up gas car-
tridges or burn hoses. Replace the accessories, if necessary.
Do not work indoors; provide good ventilation. Work only in a
clean area, away from infl ammable or greasy materials. Wear
eye protection. Do not wear greasy clothes. Avoid welding and
soldering fumes.
During work observe indications regarding: gas consumption
(at normal settings) adequately for each of the accessories and
the shelf life of the gas cartridges.
Disconnect the gas cartridge, if the unit is not to be used for a
long period or in case it is transported in a vehicle.
Store and transport gas cartridge upright. Protect them from
children.
Use only specifi ed spare parts. Do not ever use a unit with a
damaged element.
Service point: TOYA SA, ul. Sołtysowicka 13-15, 51-168 Wro-
cław, Poland.
In case of a gas leakage, it is required to immediately turn the
burner off and walk away from any source of fi re and high tem-
perature. Proceed in accordance with the information conta-
ined in safety data sheet provided along with the gas cartridge.
Head against the wind. Isolate the contaminated area and keep
bystanders away. Try to stop or at least reduce the emission
to the environment, if possible. Use adequate protection of the
respiratory tract. Spray water mist to minimise and limit the re-
lease of gas.
Bekijk gratis de handleiding van VOREL 73403, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | VOREL |
| Model | 73403 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 4334 MB |
