Vestil HBD-6-60 handleiding
Handleiding
Je bekijkt pagina 4 van 21
Table of Contents 3/30/2020 HBD MANUAL
Table of Contents Copyright 2019 Vestil Manufacturing Co. Page 4 of 21
INSTALLATION
Responsibility for compliance will local building code(s) requirements, municipal/county ordinances, etc. rests
exclusively with the end-user. The instructions that appear below are recommendations about essential, minimum
steps necessary for safe installation. If law enforced where the dumper is used requires you to depart from these
directions, Vestil is not responsible for any consequential damages sustained as a result of the installation.
Installation requires at least:
• Forklift rated for loads equal to the net weight of your HBD model (see Table on p. 2);
• Lag bolts: ½ in. by at least 4in. (length) [approximately equivalent to 1.3cm by at least 10.2cm]
• Masonry drill and ½ in. masonry drill bit
• Wrench: ½ in.
• Grout and steel shims
• Power supply circuit: matched to motor voltage and current requirements (see Label 250 in “Labeling Diagram”
on p. 21).
NOTE: End-user responsible for providing overcurrent and short circuit protection.
Step 1: Position the dumper as desired
with a forklift.
Step 2: Drill holes approximately 4in.
(10cm) deep.
Step 3: Secure the dumper to the floor by
inserting the lag bolts through the (5/8 in.)
bolt holes in the anchor brackets (dotted
lines in diagram.
Step 4: Shim and/or grout the sides of the
frame.
Step 5: Connect the power cord to the
power supply.
LOADING THE DUMPER
1. Use only properly sizes waste containers: HBD’s are designed to dump open-top containers. Container width
should be at least ½ the width of the chute, and container height should be at least ¾ the height of the chute.
2. Place the container inside the chute: the back of the container should rest against the back of the chute.
3. Insert retaining tube: to prevent the container from sliding out of the chute along with the trash, install the
container-retaining tube through the sockets that are most closely matched to the height of the container. The
top of the container should not be more than 5 inches (~12½ cm) below the tube.
4. Dump the container: press the “UP” button on the pendant controller to raise the chute to the dumping position.
The cylinders will extend, which raises the chute, only while the operator presses the “UP” button. When the
operator releases the UP button, the chute will maintain its position as of the instant the button is released.
NOTE: If the net weight of the container and its contents exceeds the maximum rated load of the dumper, a
relief valve (incorporated into the hydraulic system) will open. While the relief valve is open, the hydraulic
cylinders will not extend, and therefore the chute will not raise/dump.
5. Return the chute to the loading position: press the “DOWN” button on the controller—the cylinders will retract,
which pulls the chute toward the ground. If the DOWN button is released before the chute is completely retracted,
it will maintain its position. Always completely lower the chute.
Models rated for up to 6,000 pounds (2,727kg) include a lower limit switch that prevents the cylinders from
retracting more than necessary to lower the chute to the loading position.
Installation diagram
Concrete
Lag bolt
Lag
bolt
Lag bolt
Shim or grout
entire length
(and under left
side)
Right side
Left side
Step 6
: Run the dumper through several
complete cycles. Press the “UP” button of
the hand controller until the chute raises
as far as it can, and then lower it
completely. Repeat the cycle a few more
times to confirm
that the product operates
properly.
Step 7
: Check the oil level in the reservoir.
F
ully raise the chute (to the 45°) “dumping
position,” and then observe the level of oil
in the reservoir.
The surface of the oil
should be 1 to 1½ inches below
the fill
hole.
Bekijk gratis de handleiding van Vestil HBD-6-60, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Vestil |
| Model | HBD-6-60 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 5500 MB |
