Vestil H-200-HD handleiding
Handleiding
Je bekijkt pagina 12 van 16
Table of Contents Rev. 7/24/2024 H-Hoppers MANUAL
Table of Contents Copyright 2024 Vestil Manufacturing Company Page 12 of 16
NATIONAL STANDARDS
US OSHA Rule 1910.178 (29 CFR 1910.178; the “Rule”) classifies this device as a “front- end attachment”
whenever it is mounted on a lift truck. The Rule incorporates American National Standard ANSI/ITSDF B56.1
(the “Standard”). The Standard is published by the Industrial Truck Standards Development Foundation on
its website (www.itsdf.org) where it is freely downloadable at http://www.itsdf.org/cue/b56-standards.html.
Before putting this device into service, acquire a copy of the Standard. Apply all relevant parts of Part II: For
the User. If instructions provided in this manual apparently conflict with the Standard, then apply the
instructions in the Standard. Vestil requests that you immediately share any conflicts you discover with its
TECHNICAL SERVICE personnel. Contact information is provided on the cover page of this manual.
LOADING THE CHUTE
Verify that the hopper chute is securely latched and locked to the base frame before filling it with refuse.
Standard H-series hoppers are suitable for use indoors and outdoors and in most industrial and commercial
settings. They are designed for use with rider forklift trucks. Put only non-hazardous wastes in the chute.
USING THE CABLE AND HANDLE TO DUMP THE HOPPER
H-series hoppers have a low profile chutes that rotate through a 90° dump angle. To dump the hopper
chute using the cable and handle, simply unlock the release lever and pull the release cable.
Step 1: Mount the hopper on the forks of your lift truck. Drive forward until the forks contact the ends of the
fork slots. Securely attach the hopper to the fork carriage with the carriage chain by wrapping the free end
of the chain around part of the carriage. Then, connect the quick link at the end of the chain to a link in the
chain. There should be little to no slack in the chain.
Step 2: Store the handle of the release cable within reach of the forklift operator. For example, the handle
could be hooked to the frame of the roll cage.
NOTE: Make sure that there is slack in the cable. If the cable is taut, bumps or sudden stops while driving
might cause the chute to be released.
Step 3: Raise the forks and tilt the mast back/towards the cab. Only raise the forks a few inches above the
ground. Drive the forklift to the trash dumpster. Pull the finger tab until the latch lock disengages the latch
bar. See diagrams included in Step 4 below. Elevate the hopper above the sides of the dumpster.
Step 4: Pull the release cable to release the chute and dump its contents. The chute will pivot about the
dump axis. If necessary, tilt the mast forward/away from the cab while pulling the release cable to
encourage the chute to dump.
NEVER WRAP THE
RELEASE CABLE
AROUND ANY PART
OF YOUR BODY,
ESPECIALLY AN
ARM OR HAND!
Step 5: Return the chute to the latched position. Tilt the forklift mast toward the cab; then back away
from the dumpster. Lower the forks until the hopper contacts the ground; then slowly lower the forks the
rest of the way to the ground until the chute latches to the base frame. Confirm that the chute is
properly latched by raising the forks. The chute should not rotate. If necessary, lower the forks
completely and manually latch the chute to the frame by pressing down on the back of the chute (see
“H-series” diagram in Step 4). Alternatively, use the side of the dumpster to pivot the chute back onto
the base frame.
Step 6: Lock the latch. Press the latch lock forward until it firmly engages the latch bar.
Manual
chute
release
lever
Bekijk gratis de handleiding van Vestil H-200-HD, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Vestil |
| Model | H-200-HD |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 4701 MB |
