Vestil CBB-3000-37 handleiding
Handleiding
Je bekijkt pagina 16 van 19
TABLE OF CONTENTS Rev. 4/13/2023 CBB-3000-37 MANUAL
TABLE OF CONTENTS Copyright 2022 Vestil Manufacturing Co. Page 16 of 19
12. Unlatch the door by turning the turnbuckle wheel in the OPEN DOOR direction. Then, open the door as widely
as possible.
13. There are channels in the compacting surface of the
platen that extend from the front of the platen to the
back of the platen. Feed baling wire/strapping/twine
(baling material) through these channels until the
baling material comes out of the slots in the back of the
baler. NOTE: Do not feed baling material through the
channels marked with an X in the diagram. Bale
ejecting chains are present at the back of the baling
chamber in these locations.
14. Move to the back of the baler. Pull more of the baling
material through the channels. Insert the baling
material into the channels in the floor of the baling
chamber. Feed baling material through the channels
until the ends come out of the front of the bale.
15. Attach the yellow bale ejecting hooks to the platen.
16. Move to the front of the baler. Pull the baling material
taut and tie it off or crimp it together as appropriate.
17. Remove all cardboard scraps and other material from
the top of the platen.
18. Make sure that nobody is standing in front of the baler,
then twist the red E-STOP button clockwise until it pops
out. With the gate and the chamber door both fully
open, press and hold both the CYCLE START and UP
buttons. The platen ascends and the bale is ejected
from the chamber.
19. Clean out the baling chamber and place a full sheet of
cardboard on the floor of the chamber.
20. Disconnect the bale ejecting hooks from the platen.
Set the hooks on their holders.
The baler is now ready to make another bale by repeating
steps 3-20.
In order to achieve a short cycle time, both sections of the pump in the power unit drive oil to the
cylinder until the cylinder pressure reaches approximately 1000 PSI. At this threshold pressure, the high-
displacement, low pressure section of the pump begins to direct oil to the reservoir while the low-
displacement, high-pressure section continues to direct oil to the cylinder. This arrangement creates a High-
Low hydraulic circuit.
As the platen compacts cardboard, oil pressure increases until it reaches the set-point of the pressure
switch. The directional valve shifts and oil flows away from the cylinder. Reversing the flow of oil causes the
cylinder to retract and raise the platen to the home position. When the cylinder returns the platen to the
top of the cabinet, the power unit automatically turns off.
The ram can be stopped at any point during an AUTO cycle. Stop the ram by pressing the red
emergency stop button located on the control box. Pressing the button instantly stops the motor and
prevents the cylinder from extending any further. Disengage the E-stop button by turning it clockwise. Press
the cycle start button again to resume the cycle.
RECORD OF SATISFACTORY CONDITION (THE “RECORD”)
Record the condition of the baler/compactor before putting it into service. Thoroughly photograph the
unit from multiple angles. Include close range photographs of the power unit, door hinges and
latches/closures, the interior of the baling chamber, the compactor platen, labels, the hydraulic cylinder,
frame elements, and anchoring sites. Close the door and operate the baler through a complete cycle
(cylinder fully extended and then retracted to home position. Describe the motion of the cylinder, e.g.
smooth and at a constant rate, as well as sounds produced by the power unit and cylinder during the
cycle. Collect all photographs and writings in a single file. This file is a record of the unit in satisfactory
condition. Compare the results of all inspections to this record to determine whether the unit is in
satisfactory condition. Do not use the baler unless it is in satisfactory condition. Purely cosmetic changes,
like damaged paint/powdercoat, do not constitute changes from satisfactory condition. However,
Channel in platen Slot in back of baler
Channel in chamber floor
Bale ejecting hook
in holder
Holder
Bale ejecting hook
Bale ejecting
chain
Slot in back of baler
Bekijk gratis de handleiding van Vestil CBB-3000-37, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Vestil |
| Model | CBB-3000-37 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 5154 MB |
