USL LSS-200 handleiding
Handleiding
Je bekijkt pagina 26 van 34
22
TD-001538-01-A1
Firmware Update
QSC may offer firmware updates to add features to the LSS-200. Firmware updates are delivered as a “hex” file. To install the update, click on
“Update Firmware Page” on the “Configuration Page.” The firmware update page is shown in Figure 21 - LSS-200 firmware update page. Note that
some firmware updates may result in a change in log format. For this reason, this page includes a “Clear Log” button. This button can also be used
to clear the log for other reasons.
— Figure 21 — LSS-200 firmware update page
Follow these step-by-step instructions to do a firmware update:
1. Use the browse button to select the hex file to be loaded into the LSS-200.
2. Press “Update Main Processor.” The green LED on the LSS-200 will flash as the new firmware is installed. After the new code is uploaded to
the LSS-200, the browser will return a “Connection Reset” message. This happens when the LSS-200 reboots with the new firmware.
If a firmware update is interrupted, it is possible for the LSS-200 to cease operating. To restore the factory firmware (allowing another attempt at
the update), hold down the restore button as power is applied to the LSS-200. If the button is held for about 1 second before and 1 second after
power is applied, the factory firmware will be reloaded and system configuration will remain unchanged. The green LED flashes as the firmware is
reloaded. Once the system is up and running, pressing the restore button will restore the default IP address (169.254.1.6).
Restore Button
The restore button on the LSS-200 serves two purposes:
1. If the restore button is momentarily pressed while the LSS-200 is operating, the IP address is temporarily changed to its default IP address
(169.254.1.6). In addition, the admin username and password will return to their default values (admin, ultra). These will remain in effect until
the next power cycle. To maintain them through a power cycle, the settings need to be saved.
2. If the restore button is held down 1 second before applying power until 1 second after applying power, the factory firmware is reloaded. This
can be used if a firmware update fails and leaves the system inoperable. The green LED will flash as the firmware is reloaded. No configuration
is changed in this process. The unit will remain at the same IP address.
Useful Software
Several programs are available on the QSC LSS website that should prove useful with the LSS-200.
— Table 3 — Useful Software
URL Description
http://ftp.uslinc.com/?dir=ftp/Products/EthernetDeviceDiscoverer
Ethernet Discoverer - Finds QSC products on the network. Shows the MAC
address, IP address, host name and other information. Clicking on a listing
opens the home web page of the device. Also reports logged out of tolerance
information from the LSS-200. Windows, Android, and iOS versions are available.
http://ftp.uslinc.com/ftp/MultiProduct/Realterm_2.0.0.57_setup.zip
Real Term – A terminal program that can be used to send commands and see
responses over RS232 or TCP.
http://ftp.uslinc.com/MultiProduct/ttermp23.zip
Tera Term Pro – A terminal program that can be used to type commands to the
LSS-200 and see responses.
http://ftp.uslinc.com/?dir=ftp/Products/LSS-200/Software/TestContent
LST-200 Test DCP – Use this digital cinema content for the DCP-based
operation of the LSS-200. This DCP is also available on a flash drive from QSC.
Order part number LST-200.
http://ftp.uslinc.com/?dir=ftp/Products/LSS-DB
LSS-DB. A PHP/javascript application that reports on thousands of LSS-200 units.
Bekijk gratis de handleiding van USL LSS-200, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | USL |
| Model | LSS-200 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 6136 MB |
