Ultimate Speed UPK 10 G4 handleiding
Handleiding
Je bekijkt pagina 15 van 85
GB/IE/NI
15
Connecting the compressed air hose without a valve adapter
Screw the free end of the compressed air hose
17
directly on to the connection valve of the inflatable
item.
Connecting the compressed air hose with a valve adapter
The valve adapters
21
,
22
and
23
are located in the storage compartment for the valve adapters
14
(see Fig. B).
First screw the required valve adapter
21
,
22
or
23
to the free end of the compressed air hose
17
.
Then insert the valve adapter
21
,
22
or
23
into the connection valve of the inflatable item (if necessary
remove the valve cap of the inflatable item).
Removing the compressed air hose
Connecting without the valve adapters
21
,
22
or
23
: Unscrew the compressed connection hose
17
off
the valve of the inflatable item.
Connecting with the valve adapters
21
,
22
or
23
: First, pull the valve adapter off the connecting
valve
on the inflatable item. Unscrew the valve adapter
21
,
22
or
23
off the compressed air hose
17
(if necessary,
reattach the valve cap on to the inflatable item).
PLEASE NOTE: When disconnecting the compressed air hose
17
, air can escape from the valve
of the inflatable item. Ensure that you remove the compressed air hose
17
as quickly as possible.
Pressure-Preselect function
Switch on the power bank with compressor
1
by using the switch for the power bank
9
.
Connect the compressed air hose
17
of the power bank with compressor
1
to the inflatable item
which you want to inflate. To do so, please proceed as described in the previous section.
Use the “M” menu button
5
to select the desired unit of pressure. The units available are bar
(“bar”), kilopascal (“KPa”), kilogram per square centimetre (“KG/CM²“) and pound per square inch
(“PSI”) (see Fig. E).
Use the “+” button
3
and the “-” button
4
to select the desired pressure. To speed up the selection,
you can keep the respective button pressed down. Pressure settings between 0.3 bar and 3.5 bar
are possible in 0.05 bar steps (see Fig. E).
PLEASE NOTE: While preselecting the pressure, the digital pressure gauge with the air pressure
and battery display will flash
6
. If a button is not pressed for at least 10 seconds, the display will
display the ACTUAL value of the pressure. The pressure which has been set remains stored.
Switch on the integrated compressor by pressing the On/Off button for the compressor
2
once.
The compressor will start and pump up the inflatable item.
You can switch off the compressor at any time by pressing the On/Off button for the compressor
2
once more.
Otherwise, the compressor will switch off automatically once the inflatable item has reached the
preset pressure.
Disconnect the inflatable item from the compressed air hose
17
as described in the previous section.
At the end of work, screw the compressed air hose
17
back off the hose connection
15
of the power
bank with compressor
1
.
ATTENTION: The hose connection
15
of the power bank with compressor
1
heats up during operation.
Make sure that you do not come into contact with the hose connection
15
during operation to avoid
suffering burns. At the end of work, wait for at least 10 minutes before you unscrew the compressed air
hose
17
back off the hose connection
15
of the power bank with compressor
1
.
PLEASE NOTE: After switching on the power bank with compressor
1
with the power bank
switch
9
, the device switches off automatically after approximately 20 seconds if the compressor
is not started or if no consumables are connected.
Bekijk gratis de handleiding van Ultimate Speed UPK 10 G4, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Ultimate Speed |
| Model | UPK 10 G4 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 7847 MB |
