Handleiding
Je bekijkt pagina 6 van 20
Disconnect electrical power supply be-
fore cleaning any parts of the unit.
V. a - CLEANING THE CONDENSER:
The most important thing you can do to insure a long,
reliable service life for your Traulsen is to regularly clean
the condenser coil. The self-contained condensing unit
requires regularly scheduled cleaning to keep the nned
condenser clean of lint and dust accumulation. Keeping
the condenser clean allows the cabinet to operate more
efciently and use less energy.
To clean the self-contained condenser, rst disconnect
electrical power. To access the coil:
TBC5: Open the refrigeration compartment door on left.
TBC13: Remove the four (4) screws securing the front
louver panel at bottom and remove the panel.
TBC1H/TBC1HR: Remove the two (2) bottom screws
securing the louver assembly located on the top/front of
the cabinet and lift the louvers.
Vacuum or brush any dirt, lint or dust from the nned
condenser coil, the compressor and other cooling system
parts. If signicant dirt is clogging the condenser ns, use
compressed air to blow this clear. For care of the remote
condensing unit(s) used for models TBC1H & TBC1HR,
consult the manufacturer’s product literature.
V. b - PRINTER SUPPLIES:
Supplies to support the both standard epicon
control printers are available directly from our Parts
Department, or from your local Hobart Sales and
Service Ofce. In addition it may also be possible to
obtain one of these locally. The record printer paper is
standard thermal paper which is readily available at
most office supply outlets. Specifications are 2-1/2”
wide by 85” long:
Traulsen P/N 400-60003-00
OfceDepot#302-224
Staples#PMF-5233
The label printer uses a special peel-off label stock,
Traulsen part number 400-60004-00. Each roll contains
225 labels.
V. c - INSTALLING PRINTER PAPER:
To reload record or label paper, begin by opening the cover
or door to access the printer(s). Remove the empty paper
roll and place a new roll on spindle. Position the paper
such that the paper feeds from the back of the roll. This
allows the thermal sensitive side of the paper to be on the
upper surface as it feeds through the printer. The ends of
the spindle are installed in the roll holders on each side of
the paper cradle.
Gently pull the feed roller tension arm slightly forward. It
is located on the top of the printer and will open about 90
degrees.
-5-
V. c - INSTALLING PRINTER PAPER (cont’d):
Feed the paper down into the loading slot directly behind
the feed roller tension arm.
Return the feed roller tension arm to its original position.
If this is not closed the printer will not operate. Labels are
loaded in the same manner. Note after turning the chiller
on the label printer will automatically orient the next label
for printing.
Press the red feed button to feed paper through the printer.
Replace the printer cover or close the printer door, taking
care that the paper or label is passed through the paper
slot on it’s front.
V. d - REPLACING THE BATTERY:
Battery may explode if mistreated. Do
notrecharge,disassembleordisposeofinre.
Replace battery with Panasonic Corp. Part No. CR2032 only. Use of
another battery may present a risk of re or explosion.
Replacement batteries can be obtained from Digi-Key (www.digikey.com),
Newark (www.newark.com), or other suitable suppliers.
The epicon control includes a battery back-up for the real
time clock. Should this ever need to be replaced use the
following procedure:
Step 1: Turn off power to the blast chiller.
Step 2: Remove the top & bottom screws that hold
the bessel on the blast chiller.
Step 3: Carefully pull the assembly out of the cavity.
Step 4: Slide the battery out of it’s holder, located on
the rear bottom of the control board.
Step 5: Slide a new battery into the holder, making
sure that the positive side of the battery
faces up as indicated on the battery holder.
Step 6: Install the assembly back in place, tighten
the screws to ensure assembly is securely in
place.
Step 7: Return power to the blast chiller.
V. CARE & MAINTENANCE
Printer Architecture
WARNING
WARNING
Bekijk gratis de handleiding van Traulsen TBC13, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Traulsen |
| Model | TBC13 |
| Categorie | Koelkast |
| Taal | Nederlands |
| Grootte | 3760 MB |
