Toolson WS4100 handleiding
Handleiding
Je bekijkt pagina 22 van 248
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
22 GB
3. Health damage caused by hand-arm vibrations if
the equipment is used over a prolonged period or
is not properly guided and maintained.
4. Contact with the saw blade in the uncovered saw
zone.
5. Reaching into the running saw blade (cut injuries).
6. Kick-back of workpieces and parts of workpieces.
7. Saw blade fracturing.
8. Catapulting of faulty carbide tips from the saw
blade.
6. Technical data
AC motor: 230 V ~ 50 Hz
Power P: 1500 W S1
Power P: 2200 W S6 40%
Protection type: IP 54
Idle speed n
0
: 2800 min
-1
Saw blade: Ø 405 x Ø 30 x 3,2 mm
Number of teeth: 32
Max. cutting capacity: 135 mm
Min. cutting capacity: 30 mm
Weight: 38 kg
Operating mode S6 40%: Continuous operation with
idling (cycle time 10 minutes). To ensure that the
motor does not become excessively hot it may only
be operated for 40% of the cycle at the specied
rating and must then be allowed to idle for 60% of
the cycle.
Sound and vibration
Sound and vibration values were measured in ac-
cordance with EN 1870-6.
Mode
Sound pressure level L
pA
96 dB(A)
Uncertainty K
pA
4 dB
Sound power level L
WA
106 dB(A)
Uncertainty K
WA
4 dB
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Keep the noise emissions and vibrations to a
minimum.
• Only use appliances which are in perfect working
order.
• Service and clean the appliance regularly.
• Adapt your working style to suit the appliance.
• Do not overload the appliance.
• Have the appliance serviced whenever necessary.
• Switch the appliance off when it is not in use.
7. Assembly
Required assembly tools:
• Open-end wrench SW8, SW13, SW14
• Hexagon socket size 4
• Phillips screwdriver
7.1. Installation of the jig saw (Fig. 3)
Fastening parts from accessories kit 28 (Fig. 2.1)
2 pieces hexagon bolt M8 x 60
4 pieces washer 8 mm
2 pieces self-locking M8 hexagon bolts
Install the two cross bars (10) on the inner side of
the two stands with the two hexagon bolts and 2
washers. Now insert the sea-saw (2) with the help of
a second person on the hexagon bolts on the outer
side of the stands and join the bracket of the sea-saw
with the self-locking nut and a washer tightly, so that
the sea-saw cannot be moved.
7.2. Installation of recoil spring (Fig. 4)
Fastening parts:
1 piece spring
Installed on the connecting tube:
1 piece washer D 15
1 piece hexagon bolt M 6 x 25
1 piece stop nut M6
2 pieces washer 6 mm
Push the spring (A) and washer D15 on the connect-
ing tube, insert it into the angle and secure the tube
with the hexagon bolt M 6 x 25, 2 washers and one
stop nut M6 at the left of the two holes.
7.3. Installation of chain (Fig. 5)
Fastening parts from accessories kit 28 (Fig. 2.1)
1 piece hexagon bolt M 6 x 25
2 pieces washer D 6 mm
1 piece stop nut M6
Install the chain at the left side with the hexagon bolt
M 6 x 25, 2 washers and the stop nut on the sea-saw.
7.4. Installation of the saw blade cover at the out-
side left (Fig.6)
Fastening parts from accessories kit 28 (Fig. 2.1)
1 piece hexagon screw M 8 x 15
1 piece hexagon screw M 8 x 35
2 pieces washer 8 mm
2 pieces stop nut M 8
Already pre-installed:
1 piece counter sunk screw M 6 x 15
1 piece washer D 6mm
1 piece stop nut M 6
Install the saw blade cover inside with a counter sunk
screw M6 x 15, washer and a stop nut in the upper
hole of the base frame (1) with a hexagon bolt M8
x 15, washer and stop nut M8 in the lower hole at
the right of the motor plate (2) and with a hexagon
bolt M8 x 35 in the lower hole at the left on the base
frame (3).
Now tighten all the screws.
7.5. Install saw blade guard at the inside left (Fig.
7)
Pre-installed fastening parts:
1 piece socket head screw M 6 x 12
1 piece cross head screw M 5 x 20
1 piece washer 5 mm
1 piece stop nut M 5
1 piece nut M 6 as spacer
Install the saw blade guard at the inside left (1) of the
sea-saw (2) with a socket head screw M6 x 12 (3).
Install the cover plate (4) on the saw blade guard (1)
with a cross head screw M5 x 20, washer and stop
nut M5.
Bekijk gratis de handleiding van Toolson WS4100, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Toolson |
| Model | WS4100 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 42481 MB |
