Toolson TS3100PRO handleiding
Handleiding
Je bekijkt pagina 23 van 196
23 І 196
Assembly of the longitudinal fence, Fig.17 / 17.1 /
17.2
1 Mount the guide rail (A) with two hexagon bolts M6 x
16 with nuts M6 (B) to the front side of the table.
2 Mount the two clamping levers (C) to the table and the
guide rail using two lock bolts M6 x 25.
3 Place the swinging part (D) into the guide rail, set
the scale to 0°, and rmly tighten the clamping handle (E).
Attention: For longitudinal cutting, the swinging part
must always be set to 0.
4 Depending on the type of job, push the guide
rail (G) into the guide bolts (F) with the high (Fig. 18.1)
or low surface (Fig. 18.2) and tighten them rmly.
5 Set the fence rail to the desired dimension and
tighten both clamping levers (C).
Assembly of the cross-cutting gauge, Fig. 18.1 / 18.2
/ 18.3
1 Mount the guide rail with two hexagon bolts M6 x 16
and two nuts M6 to the left side of the table.
2 Place the swinging part (D) into the guide rail. The
swinging part must slide easily.
3 Depending on the type of job, push the guide rail (G)
into the guide bolts (F) with the high (1) or low surface
(2) and tighten them rmly.
4 Set the fence rail (G) to the desired degree between
+60° and -60° and tighten the clamping handle (E).
Changing the sawblade, Fig. 19
Caution! Pull out the main plug and wear safety
gloves.
Release the wing screw of the suction hood (20) and
remove the hood.
Fig. 20
Release the 4 Phillips screws of the table insert (19) and
remove the insert.
Fig. 21
Move the saw blade to the very top and release the bolt
with the saw blade key.
Attention: Left-handed thread.
Fig. 22
Remove the saw blade ange (31) and the saw blade
(32). Then change the saw blade.
When mounting the saw blade mind the recess.
After changing the saw blade, check the setting of the
riving knife and ret the table insert (19) and the suction
hood (20).
Transport
The machine may only be transported with suitable
lifting devices (crane or fork lift). The connection point
for the rope (crane) is on the upper band wheel cabi-
net. Never lift from the saw bench. If the machine is to
be moved frequently within the work area, use of the
wheel assembly special accessory is recommended.
Fig. 6 / 6.1
Fasten 2 longitudinal braces (10) and 2 cross braces (9)
onto the base legs (2, 3,4 and 5) using 12 hexagon bolts
M6 x 16, 12 washers 6, and 12 nuts M6.
Fig. 7 / 7.1 / 7.2 / 7.3
Fasten the table extension plate (8) with 2 braces 11 and
cross brace to the table top using 6 hexagon bolts M6 x
16, 6 washers 6, and 6 nuts M6.
Tighten the bolts slightly by hand. (The table length ex-
tension (8) can also be used as table width extension by
tting it to the side with the shorter braces.)
Fig. 8
Fasten the suction piece (14) to the lower saw blade
guard (13) using 4 hexagon bolts M4 x 10.
Fig. 9
Fasten the wheel assembly (16) to the rear base legs (4
and 5) using 4 hexagon bolts M6 x 16, 4 washers 6, and
4 nuts M6.
Fig. 10
Place the machine on its feet and rmly tighten all bolts
of table, legs and braces (except those of the wheel as-
sembly).
Fig. 11
Firmly tighten the wheel assembly in the position where
the wheels slightly touch the ground.
Fig. 12 / 12.1
Fasten the riving knife in line with the saw blade as de-
scribed in the illustration. Slightly release the bolt without
removing it. Retighten it rmly after resetting. For doing
this, it is necessary to remove the saw blade insert (19,
Fig. 13).
Fig. 13
After setting the riving knife, refasten the saw blade in-
sert (19) with 4 countersunk bolts M6 x 16.
Fig. 14
Fasten the cover (20) to the riving knife (18) with round-
head bolt M6 x 25, washer 6, and wing nut M6.
Fig. 15
Connect the suction hose (21) to the suction hood (20)
and the suction nozzle.
Fig. 16 / 16.1
Fasten the hooked bolt to the right-hand leg side using
2 washers 6 and 2 nuts M6. The hook serves for storing
the saw blade key and the push stick.
The 2 transport handles are attached at the left and right
leg at the front of the saw using 4 hexagon bolts M6 x 16,
4 washers 6, and 4 nuts M6.
Bekijk gratis de handleiding van Toolson TS3100PRO, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Toolson |
| Model | TS3100PRO |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 34858 MB |
