Toolson TS3100PRO handleiding
Handleiding
Je bekijkt pagina 22 van 196
22 І 196
Wear hearing protection.
The effects of noise can cause a loss of hearing. Total
vibration values (vector sum - three directions) deter-
mined in accordance with EN 61029.
Before starting the equipment
• All covers and safety devices have to be properly t-
ted before the equipment is switched on.
• It must be possible for the blade to run freely.
• When working with wood that has been processed
before, watch out for foreign bodies such as nails or
screws, etc.
• Before you press the ON/OFF switch check that the
saw blade is tted correctly. Moving parts must run
smoothly.
• Before you connect the equipment to the power sup-
ply make sure the data on the rating plate are dentical
to the mains data.
• Connect the machine to a properly installed protec-
tive contact socket, with at least 16A circuit breaker.
Attachment
Important. Pull out the power plug before carrying
out any maintenance, resetting or assembly work on
the circular saw!
Place all parts supplied on a at surface. Grouping
equal parts.
Note: If compounds with a bolt (round head / or hexa-
gon), hex nuts and washers are backed up, the washer
must be tted under the nut.
Insert screws each from outside to inside. Secure con-
nections with nuts on the inside.
Note: Tighten the nuts and bolts during assembly only
to the extent that they can not fall down.
If you tighten the nuts and bolts prior to nal assembly,
nal assembly can not be performed.
Fig. 1
Place the table top (1) onto a work bench after having
removed the packing pad a underneath the motor.
Fig. 1.1
Fasten the base leg (2) onto the table top using 2 hexa-
gon bolts M6 x 16, 2 washers 6 and 2 nuts M6. Tighten
the bolts slightly by hand.
Fig. 2
Fasten the switch (6) to the table top using 2 hexagon
bolts M6 x 16, 2 washers 6, and 2 nuts M6.
Fig. 3
Fasten the base leg (3) to the table top using 2 hexagon
bolts M6 x 16, 2 washers 6, and 2 nuts M6.
Fig. 4
Fasten the base leg (4) to the table top using 2 hexagon
bolts M6 x 16, 2 washers 6, and 2 nuts M6.
Fig. 5
Fasten the base leg (5) and the hose holder to the table
top using 2 hexagon bolts M6 x 16, 2 washers 6, and 2
nuts M6.
tool and is properly fastened.
12 Only use the supplied saw blade for sawing opera-
tions in wood, materials similar to wood, plastics
and non-ferrous metals (except for magnesium and
alloys containing magnesium).
Residual risks
The machine has been built according to the state of
the art and the recognised technical safety require-
ments. However, individual residual risks can arise
during operation.
• Health hazard due to electrical power, with the use of
improper electrical connection cables.
• Furthermore, despite all precautions having been met,
some non-obvious residual risks may still remain.
• Residual risks can be minimised if the „safety instruc-
tions“ and the „Proper use“ are observed along with
the whole of the operating instructions.
• Do not load the machine unnecessarily: excessive
pressure when sawing will quickly damage the saw
blade, which results in reduced output of the machine
in the processing and in cut precision.
• When cutting plastic material, please always use
clamps: the parts which should be cut must always
be xed between the clamps.
• Avoid accidental starting of the machine: the oper-
ating button may not be pressed when inserting the
plug in an outlet.
• Use the tool that is recommended in this manual. In
doing so, your saw provides optimal performance.
• Hands may never enter the processing zone when the
machine is in operation. Release the handle button
and switch off the machine prior to any operations.
• Prior to any adjustment, maintenance or service work
disconnect the mains power plug!
Technical Data
AC motor 230V~ 50Hz
performance 2200 W
operating mode S6 40%*
Idle speed 2800 min
-1
Hard-metal blade ø 315 x ø 30 x 3 mm
Number of teeth 24
table size 800 x 550 (950) mm
Cutting height max. 90° 83 mm
Cutting height max. 45° 49 mm
height adjustment 0 - 83 mm
saw blade swivel 0 - 45°
weight 44 kg
* operating mode S6 40%: Continuous operation with inter-
mittent loading (playing time 10 min).
Engine protection of to hot warming up:
It´s allowed to run the engine with nominal power maximum
40% of playing time. After this the machine must run 60% of
playing time steadily without load.
Noise values
The total noise values determined in accordance with
EN 61029.
sound pressure level L
pA
94,5 dB(A)
uncertainty K
pA
3 dB
sound power level L
WA
105,2 dB(A)
uncertainty K
WA
3 dB
Bekijk gratis de handleiding van Toolson TS3100PRO, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Toolson |
| Model | TS3100PRO |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 34858 MB |
