Tascam FR-AV2 handleiding
Handleiding
Je bekijkt pagina 32 van 72
32 TASCAM FR-AV2 V1.00
6. I/O SETTINGS
Setting the equalizer (EQ)
The equalizer has the eect of amplifying and attenuating specic
frequency ranges. This can be used, for example, to enhance the
sound of individual instruments, to adjust the balance of a wide
frequency range and to cut specic unwanted frequencies.
OFF (default)
This disables the equalizer.
INTERVIEW
This setting is good for recording sound in interviews, meetings,
podcasts and similar conversational situations.
MUSIC
The setting is good for emphasizing heavy low frequencies in
band performances, for example.
MANUAL EQ
With this setting, four bands can be adjusted manually. In
addition to low-frequency and high-frequency boosts, two
peak curves can be set.
Gain knobs (HIGH, H-MID (high mid), L-MID (low mid), LOW)
These set the amounts levels are increased or decreased for
each band.
Ranges
GAIN: −12 dB – +12 dB (0 dB by default)
FREQ knobs (HIGH, H-MID, L-MID, LOW)
These set the cuto frequencies of the HIGH and LOW bands
and the middle frequencies of the H-MID and L-MID bands.
Ranges
HIGH: 1.7 kHz – 18.0 kHz (5.5 kHz by default)
H-MID: 32 Hz – 18.0 kHz (1.7 kHz by default)
L-MID: 32 Hz – 18.0 kHz (1.7 kHz by default)
LOW: 32 Hz – 1.6 kHz (400 Hz by default)
Q knobs (H-MID/L-MID)
These set the acuteness of these bands.
The higher the value is the more acute it becomes, making it
aect a narrower frequency band around the set frequency.
The lower the value is the less acute it becomes, making it
aect a broader frequency band around the set frequency.
Ranges
H-MID: 0.25 – 16.00 (default 2.00)
L-MID: 0.25 – 16.00 (default 2.00)
MANUAL EQ
This 4-band parametric EQ can be adjusted manually.
e
Use the m[d], F2[ ],
F3[ ] and ,[e] buttons
to select the knob to adjust
and press the F4[ENTER]
button.
Use the F2[hPARAM] and
F3[PARAM7] buttons to
adjust.
Press the F4[ENTER] button
to enable knob selection
again.
Examples of EQ characteristics
-3dB
FREQ
GAIN
LOW HIGHLOW-MID HIGH-MID
-3dB
FREQ
GAIN
FREQ
GAIN
Q が小さい Q が大きい
Low Q High Q
Setting the noise gate (NOISE GATE)
Sound below a set level can be muted.
When “LOW” is selected, only quiet sounds will be muted. When
“HIGH” is selected, sounds up to a certain level will also be muted.
Options: OFF (default), LOW, MID, HIGH
Inverting the input phase
(PHASE INVERT)
Turning this on will invert the phase.
Select PHASE INVERT and press the F4[ENTER] button to switch
the setting.
Options: OFF (default), ON
NOTE
If the sound seems to be unclear when recording the same
source with more than two or more mics, inverting the phase
of one or more inputs could improve the sound quality.
Bekijk gratis de handleiding van Tascam FR-AV2, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Tascam |
| Model | FR-AV2 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 8478 MB |
