Supermicro X14SAE handleiding
Handleiding
Je bekijkt pagina 10 van 11
ContaCt InformatIon
• www.supermicro.com (Email: support@supermicro.com)
• Manuals: https://www.supermicro.com/support/manuals
• Drivers & Utilities: https://www.supermicro.com/wdl/driver/
• Safety: https://www.supermicro.com/about/policies/safety_information.cfm
The X14SAE/X14SAE-F motherboard supports a single Intel Core
TM
Ultra 5/7/9 series processor (LGA 1851), up to 192 GB of Unbuffered
(UDIMM) ECC/Non-ECC DDR5 memory with speeds of up to 5600 MT/s in four 288-pin memory slots. Populating these DIMM slots
with a pair of memory modules of the same type and size will result in interleaved memory, which will improve memory performance.
Notes: 1) For memory optimization, use only DIMM modules that have been validated by Supermicro. For the latest memory updates, please refer to our
website at https://www.supermicro.com/products/motherboard.
2) Always connect the power cord last, and always remove it before adding, removing, or changing any hardware components.
3) Overheating can seriously damage CPU and motherboard. Always make sure cooling fans function properly to protect CPU from overheating.
Memory Population Guidelines
When installing memory modules, the DIMM slots should be populated in the following order: DIMMB2, DIMMA2, DIMMB1, DIMMA1.
• To optimize memory performance, please use (DDR5) memory of the same type, size, and speed on the motherboard.
• Mixed DIMM speeds can be installed. However, all DIMMs will run at the speed of the slowest DIMM.
• In a given channel, the black slot will be enabled only when the gray slot is populated rst.
• The DDR5 DIMM module is NOT hot-swappable and be sure to disconnect power for a minimum of 20 seconds before inserting
or removing it.
• Removing a DDR5 DIMM module at a slanted angle will cause damages. It is strongly recommended that you lift the module
straight up out of the slot.
DIMM Memory Installation
Jumpers
CPU and Memory Support
Jumper Description Default
JBT1 Clear CMOS (Onboard) Short Pads to Clear CMOS
JD1 External Speaker/Buzzer
Pins 1–4: External Speaker
Pins 3–4: Buzzer (Default)
JPAC1 HD Audio Enable/Disable Pins 1–2 (Enabled)
JPCIESW CPU PCIe SLOT3 1x8/2x4 Pins 1–2 (SLOT3 1x8)
JPG1 VGA Enable/Disable (X14SAE-F only) Pins 1–2 (Enabled)
JPL1, JPL2 LAN1/LAN2 Enable/Disable Pins 1–2 (Enabled)
JPME2 ME Manufacturing Mode Pins 1–2 (Normal)
JPT1 Onboard TPM 2.0 Enable/Disable Pins 1–2 (Enabled)
JWD1 Watchdog Function Enable Pins 1–2 (Reset)
Jumpers
Memory Support
Frequency
4400 MT/s
(2DPC)
4800 MT/s
(2DPC)
5600 MT/s
(1DPC)
DIMMA1 2R DIMM 1R DIMM N/A
DIMMA2 2R DIMM 1R DIMM
1R or
2R DIMM
DIMMB1 2R DIMM 1R DIMM N/A
DIMMB2 2R DIMM 1R DIMM
1R or
2R DIMM
Recommended Population (Balanced)
DIMMA1 DIMMB1 DIMMA2 DIMMB2
Total
System Memory
8 GB DIMM 8 GB DIMM 16 GB
8 GB DIMM 8 GB DIMM 8 GB DIMM 8 GB DIMM 32 GB
16 GB DIMM 16 GB DIMM 32 GB
24 GB DIMM 24 GB DIMM 48 GB
16 GB DIMM 16 GB DIMM 16 GB DIMM 16 GB DIMM 64 GB
32 GB DIMM 32 GB DIMM 64 GB
24 GB DIMM 24 GB DIMM 24 GB DIMM 24 GB DIMM 96 GB
48 GB DIMM 48 GB DIMM 96 GB
32 GB DIMM 32 GB DIMM 32 GB DIMM 32 GB DIMM 128 GB
48 GB DIMM 48 GB DIMM 48 GB DIMM 48 GB DIMM 192 GB
Towards the CPU
DIMMA2 (Gray Slot)
DIMMB2 (Gray Slot)
DIMMB1 (Black Slot)
DIMMA1 (Black Slot)
Bekijk gratis de handleiding van Supermicro X14SAE, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Supermicro |
| Model | X14SAE |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 1852 MB |
