Steinbach FXS38 handleiding
Handleiding
Je bekijkt pagina 12 van 15
22 23
040603_V2405 040603_V2405
Installaon
Some hoses are very s. Place them in the sun before installaon so that they become more exible
due to the heat.
Integrate the device into the water circuit
Observe the layout diagram according to Figure B.
» Connect the hoses for the water supply and drainage to the appliance.
» Recommended addional material: Swimming pool hoses Ø 32 mm and hose clamps as required.
Connecon to Ø 38 mm installaon:
The appliance can be connected to a Ø 38 mm hose using the double hose nozzle (060034) and hose clamps
(060038).
Connecon to INTEX hose with 2“ union nut:
With a 2“ double nipple (062085), at gasket (0409331) and the adapter A - 2“ female thread / Ø 32/38 mm
(110849), the device can be connected to an INTEX hose with a 2“ union nut.
You can nd suitable adapters in our webshop at: www.steinbach-group.com
Proceed as follows to connect a swimming
pool hose to the pump or lter vessel:
1. Guide a hose clamp over the hose.
2. Push the hose onto the hose connecon.
3. Secure the hose clip to the hose connecon
using a PH1 Phillips screwdriver.
The plugged swimming pool hose is ed.
Prepare the lter system
Venng the appliance
» When commissioning the appliance for the
rst me, please note that it must be vented
manually.
» To do this, observe the item numbers in gure A and unscrew the bleed screw
3
from the appliance.
» Water must run into the lter housing on its own.
» If water comes out of the vent opening, close it again with the vent screw
3
.
Establish power supply
Operaon with PV panel
» Connect the connecon cable of the device to the PV panel and ghten the union nut by hand.
Operaon with oponal power supply unit
» When operang with mains voltage, only use the oponal mains adapter.
» The appliance may only be connected to a circuit protected by an RCD switch (residual current device) with
a tripping current of 30 mA.
» Connect the connecon cable of the appliance to the power supply unit and ghten the union nut by hand.
Operaon
WARNING!
Danger to life due to operaon of the water treatment system while bathing!
Hair or items of clothing can be sucked into the sucon opening of the pool and, in extreme cases, trap people
under water and prevent them from surfacing.
» Never operate water treatment system devices while people are in the pool.
» Prevent all access to the pool while water treatment system devices are in operaon.
ATTENTION!
Risk of injury!
A damaged device or damaged accessories can lead to injuries.
» Check the appliance and accessories (see chapter Checking).
NOTE!
Flocculants in the bath water can cause the Filter Balls or Filter Wool Flakes to clump together and severely
impair their cleaning eect.
» Do not use occulants for water treatment if you are using Filter Balls or Filter Wool Flakes as a lter
medium.
Commissioning
Ensure that all hoses and pipes are connected correctly and that the water level in the pool is at least 2.5 to 5
cm above the opening of the sucon pipe.
Operaon with PV panel
If the device is operated with the PV panel, the pump starts operang automacally when there is sucient
sunlight.
Operaon with oponal power supply
If the device is operated with the power supply unit from the accessories, operaon starts as soon as the
power supply has been established.
Maintenance instrucons
Algae, bacteria and other microorganisms cannot be ltered by the device.
» Use special water care products to prevent and remove them in order to ensure hygienically perfect water.
» Seek advice from a specialist and observe the dosing quanes.
Maintenance
Change lter medium
The lter medium used (Filter Balls or Filter Wool Flakes) is subject to a certain amount of wear and tear, even
when operated as intended under opmum condions, and should be replaced at regular intervals depending
on the operang me and degree of soiling.
4. Switch o the appliance by unplugging the mains plug or disconnecng the PV panel.
5. Close the shut-o valves or block the water ow to the connecng hoses of the pool.
6. Disconnect the connecng hoses from the pool and the appliance.
7. Completely drain the water from the lter vessel.
8. Dismantle the clamping ring.
de de
Bekijk gratis de handleiding van Steinbach FXS38, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Steinbach |
| Model | FXS38 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 3704 MB |
