SRS DC215 handleiding

Handleiding

123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175176177178179180181182183184185186187188189190191192193194195196/ 196

Afdrukken

Je bekijkt pagina 25 van 196

Manual Conventions and Organization iii

Stanford Research Systems DC215 Voltage/Current Source

Example 2: Setting the Output

This section describes how to connect the unit to the DMM and set the source voltage

using the DC215s user interface.

Voltage Output

1) Connect the DC215 Output terminals (Hi and Lo) to the DMM voltage input

terminals (Hi and Lo) with banana cables. Turn on the DMM, set it to DC

voltage and autorange.

2) Press [ON/OFF] to turn on the Output. Observe the voltage on the DMM (~0.0

mV). The DC215 current monitor should read ~0.0 mA since there is no load.

3) Type [1] [0] [V/A] to set the source voltage to +10.0000 V. The DMM should

read very close to +10.0000 V. The DC215 current monitor may read up to

~0.001 mA depending on the input impedance of the DMM.

4) Press the [←] cursor key. Notice that the least significant digit begins to flash.

Press the [↑] cursor key four times to change the source voltage to +10.0004

V. The DMM should read very close to +10.0004 V.

5) Press the [↓] RANGE key to change the source range to 1V which is indicated

by the “rAnGE 1V” message. Observe that the source voltage was coerced to

0.00000 V, since the previous 10 V setting is outside of the 1V range.

6) Type [±] [1] [V/A] to set the source voltage to -1.00000 V. The DMM should

read very close to -1.00000 V.

Current Output

7) Press [ON/OFF] to turn the output off. Press [V/I] to change to current output.

8) Connect the DC215 Output terminals (Hi and Lo) to the DMM current input

terminals (Hi and Lo) with banana cables. Set the DMM to DC current and

autorange.

9) Press [ON/OFF] to turn the Output. Observe the voltage on the DMM (~0.0

mA). The DC215 voltage monitor should read ~0.0 mV since there is no load.

10) Type [1] [0] [mV/mA] to set the source current to 10.0000 mA. The DMM

should read very close to +10.0000 mA. The DC215 voltage monitor may read

up to ~100 mV depending on the burden resistance of the DMM.

11) Press the [↑] RANGE key to change the source range to 100mA indicated by

the “rAnGE 100m” message. Observe that the source current is still set to

10.000 mA, since the previous 10 mA setting is within the 100mA range. The

DMM and DC215 voltage monitor should read the same as on the previous

step.

12) Press [ON/OFF] to turn the output off.

123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175176177178179180181182183184185186187188189190191192193194195196/ 196

Bekijk gratis de handleiding van SRS DC215, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.

Productinformatie

Andere merken in Niet gecategoriseerd