Speed Queen FV6010WN handleiding
Handleiding
Je bekijkt pagina 86 van 119
Hold Step Custom Messages CNESS-
This option allows the owner to program the machine to display a
custom hold step message when a hold step is programmed.
1. Control must be in Manual Mode. Refer to How to Enter the
Manual Mode.
2.
Press the DELICATE (∧) or the HOT (∨) keypad until Prog
appears in the display. Press the START (enter) keypad, and
AtS 1 will appear in the display.
3. Press the DELICATE (∧) or the HOT (∨) keypad to scroll
through the programmable options until CNESS- appears in
the display.
4.
When CNESS- appears in the display, press the START (en-
ter) keypad. There are two programmable Hold Step Custom
Message options.
Display
Hold Step Custom
Message Options
CNESS1
Custom Message #1
CNESS2
Custom Message #2
Table 23
5. Press the DELICATE (∧) or the HOT (∨) keypad to change
the current option.
6. Press the START (enter) keypad to change the first of six pro-
grammable characters.
NOTE: To go back to the current programmable op-
tion without changing the value, press the WARM (<)
keypad.
7. Press the DELICATE (∧) or the HOT (∨) keypad to change
the active character and the START (enter) keypad to enter
the value of the character and advance to the next character.
8. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Programmable Cycle Time Display
PCyCtd
This option allows the owner to program the machine to display a
chosen cycle time in minutes instead of the calculated cycle time.
The cycle time display will not pause for fills . The display will
switch to 01 if the end of the cycle is reached before the time dis-
play reaches 01. If the time displayed reaches 01 before the end
of the cycle, the display will pause at 01 until the cycle ends.
In order to use this option, the owner must set the programmable
cycle time in a cycle to a value greater than 0. Refer to How to
Enter Cycle Programming CyCLE- .
1. Control must be in Manual Mode. Refer to How to Enter the
Manual Mode.
2.
Press the DELICATE (∧) or the HOT (∨) keypad until Prog
appears in the display. Press the START (enter) keypad, and
AtS 1 will appear in the display.
3. Press the DELICATE (∧) or the HOT (∨) keypad to scroll
through the programmable options until PCyCtd appears in
the display.
4.
When PCyCtd appears in the display, press the START (en-
ter) keypad. The current Cycle Time Display value will ap-
pear in the display.
on = Cycle time displayed as programmed
oFF = Calculated remaining cycle time is displayed (factory de-
fault setting)
5. Press the DELICATE (∧) or the HOT (∨) keypad to change
the current value.
6. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
No Cycle Time Display nCyCtd
This option allows the owner to program the machine to display
no cycle time instead of the cycle time being displayed, a single
dashed line will move horizontally across the display for the en-
tire cycle.
1. Control must be in Manual Mode. Refer to How to Enter the
Manual Mode.
2.
Press the DELICATE (∧) or the HOT (∨) keypad until Prog
appears in the display. Press the START (enter) keypad, and
AtS 1 will appear in the display.
3. Press the DELICATE (∧) or the HOT (∨) keypad to scroll
through the programmable options until nCyCtd appears in
the display.
4.
When nCyCtd appears in the display, press the START (en-
ter) keypad. The current No Cycle Time Display status will
appear in the display.
on = Option Enabled
oFF = Option Disabled (factory default setting)
5. Press the DELICATE (∧) or the HOT (∨) keypad to change
the current status.
6. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Number of Balance Attempts with No
Loss of Time bAL At
This option allows the owner to program the machine's number of
balance attempts with no loss of time. If the machine needs to re-
balance for any reason, time will pause for additional balance at-
tempts when this parameter is greater than 1. A value of 1 allows
for the normal allocated time. Further attempts beyond the pro-
Programming Control
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
86 Part No. 807870ENR4
Bekijk gratis de handleiding van Speed Queen FV6010WN, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Speed Queen |
| Model | FV6010WN |
| Categorie | Wasmachine |
| Taal | Nederlands |
| Grootte | 14039 MB |
