Scheppach TS30 handleiding
Handleiding
Je bekijkt pagina 32 van 56
www.scheppach.com
32
|
GB
Fitting the longitudinal stop, Fig. 17 / 17.1
• Connect the bearing piece to the clamping plate.
Mount the clamping plate to the tabletop with 2 M6
x 30 cylinder screws, 2 A 6.4 serrated washers and
2 hexagonal nuts.
Installing the stop rail, Fig. 18
• Mount the intermediate plate to the longitudinal stop
with 2 M6 x 50 at round screws, 2 A 6 washers and
2 wing nuts.
• Slide the stop rail onto the intermediate plate and
clamp it with the wing nuts.
• Legend:
1 = High contact surface
2 = Low contact surface
• To clamp, pull the clamping ap up; to release, press
it down.
Saw blade replacement, Fig. 19
m Attention! Pull out the mains plug and wear protec-
tive gloves.
• Loosen the wing screw from the suction hood (20)
and remove it.
Fig. 20
• Loosen the 4 Phillips screws from the table inlay (19)
and remove it.
Fig. 21
• Set the saw blade all the way up and loosen the
screw with the saw blade key.
Attention! Left-handed thread
Fig. 22
• Remove the saw blade ange (31) and then the saw
blade (32).
• Now change the saw blade (32).
• When mounting the saw blade ange (31), pay atten-
tion to the recess.
• After changing the saw blade, check the riving knife
setting and ret the table inlay (19) and suction hood
(20).
• Tighten the bolts lightly by hand. (The tabletop (8)
can also be mounted laterally as a table width exten-
sion with the shorter struts)
Fig. 8
• Fit the suction port (14) to the lower saw blade guard
(13) with 4 M4 x 10 hexagonal bolts and 4 x washers
4.
Fig. 9
• Mount the travel xture (16) to the rear frame legs (4
and 5) with 4 M6 x 16 hexagonal bolts, 4 washers 6,
and 4 M6 nuts.
Fig. 10
• Place the machine on its feet, tighten all screws of
the table, feet and struts (except the travel xture).
Fig. 11
• Tighten the travel xture in position such that the
wheels lightly touch the oor.
Fig. 12 / 12.1
• Mount the riving knife (18) to the saw blade (32) as
described in the illustration (12/12.1).
• Loosen the screw slightly (do not unscrew it com-
pletely) and tighten it again after the adjustment. In
doing so, the saw blade insert (19, Fig. 13) must be
removed.
Fig. 13
• After adjusting the riving knife (18), ret the saw
blade insert (19) with 4 M6 x 16 ange head screws.
Fig. 14
• Fit the cover hood (20) to the splitting wedge (18)
with a round-headed M6 x 25 screw, washer 6 and
M6 wing nut.
Fig. 15
• Connect the suction hose (21) to the suction hood
(20) and the suction port (14).
Fig. 16 / 16.1
• Fasten the hook bolt with 2 washers 6, 2 M6 nuts on
the right frame leg side. The saw blade key and the
push stick are hung on it.
• The two transport handles are mounted on the front
of the saw, on the left and right legs with 4 M6 x 16
hexagonal bolts, 4 washers 6, 4 M6 nuts.
Bekijk gratis de handleiding van Scheppach TS30, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Scheppach |
| Model | TS30 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 8355 MB |
