Scheppach HC24x handleiding
Handleiding
Je bekijkt pagina 25 van 288
www.scheppach.com
GB
|
25
The printing of the type designation on the connection
cable is mandatory.
AC motor
• The mains voltage must be 220 - 240 V~.
• Extension cables up to 25 m long must have a
cross-section of 1.5 mm².
Connections and repairs
Connections and repair work on the electrical equip-
ment may only be carried out by electricians.
Please provide the following information in the event
of any enquiries:
• Type of current for the motor
• Machine data - type plate
• Motor data - type plate
11. Cleaning, maintenance, storage
and ordering spare parts
m Attention!
Pull out the mains plug before carrying out any
cleaning or maintenance work! Danger of injury
due to electric shocks!
m Attention!
Wait until the device has cooled down completely! Dan-
ger of burns!
m Attention!
Depressurise the device before carrying out any clean-
ing or maintenance work! Danger of injury!
11.1 Cleaning
• Keep protective devices, air vents and the motor
housing as free of dust and dirt as possible.
• We recommend that you clean the device directly
after every use.
• Rub the device clean with a clean cloth or blow it o
with compressed air at low pressure.
• Clean the device at regular intervals using a damp
cloth and a little soft soap. Do not use any cleaning
products or solvents; they could attack the plastic
parts of the device. Make sure that no water can
penetrate the device interior.
• The hose and injection tools must be disconnected
from the compressor before cleaning. The compres-
sor must not be cleaned with water, solvents or similar.
9.4 Mains power connection
• The compressor is equipped with a mains cable
with an earthed plug. This can be connected to any
mains socket 230 V~ / 50 Hz with an earth contact
and that is protected at 16 A.
• Before commissioning, ensure that the mains volt-
age matches with the operating voltage and the ma-
chine's power rating on the type plate.
• Long supply lines, as well as extensions, cable
drums etc. cause voltage drop and can prevent the
motor from starting.
• At low temperatures below +5 °C, sluggishness may
make starting dicult or impossible.
10. Electrical connection
The electrical motor installed is connected and
ready for operation. The connection complies with
the applicable VDE and DIN provisions. The custom-
er's mains connection as well as the extension cable
used must also comply with these regulations.
When working with spray attachments and during tem-
porary use outdoors, the device must be connected to
a residual current circuit breaker with a trigger current
of 30 mA or less.
Damaged electrical connection cable.
The insulation on electrical connection cables is often
damaged.
This may have the following causes:
• Pressure points, where connection cables are
passed through windows or doors.
• Kinks where the connection cable has been improp-
erly fastened or routed.
• Places where the connection cables have been cut
due to being driven over.
• Insulation damage due to being ripped out of the wall
outlet.
• Cracks due to the insulation ageing.
Such damaged electrical connection cables must not be
used and are life-threatening due to the insulation damage.
Check the electrical connection cables for damage regu-
larly. Ensure that the connection cables are disconnected
from electrical power when checking for damage.
Electrical connection cables must comply with the ap-
plicable VDE and DIN provisions. Only use connection
cables with the designation H05VV-F.
Bekijk gratis de handleiding van Scheppach HC24x, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Scheppach |
| Model | HC24x |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 40205 MB |
