Scheppach DS940 handleiding

Niet gecategoriseerd

Scheppach

68 pagina's

PDF beschikbaar

Handleiding

 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58

Connect the exible suction hose (13) with the con-

nection (B) on the dust bag (15). Attach the shoulder

strap (15) to the eyelets on the dust bag (15). To emp-

ty the dust bag (15) open the zip fastener (C). (Fig. 5)

8.5. Function of the brushed edge (g. 3)

The grinding head of this power tool is enclosed by a

brush edge (A) which offers the following two advan-

tages:

a) The brush edge (A) protrudes beyond the grind-

ing plate (1) and touches the surface to be pro-

cessed rst. Thus, the grinding plate is positioned

in parallel to the working area before the insertion

tool comes in contact with the surface which is

to be processed. This is to prevent the formation

of sickle-shaped recesses caused by the grinding

disk edge.

b) Furthermore, the brush edge (A) prevents the

generation of excessive dust. Dust generated

during the grinding process is not transported to-

wards the outside but is removed by the extrac-

tion system. Make sure before each operation

with this power tool that the brush edge (A) is not

damaged. Have it replaced if there is damage or

wear.

8.6. Connection to the power supply

1. Make sure that the power tool is switched off.

2. Plug the power plug into a correctly installed

socket which complies with the requirements

specied in the technical data.

3. Your power tool is now ready for operation.

8.7. Switching on/off (g. 6)

To switch on:

Push the on/ off switch (12)

Continuous operation

Secure the on/off switch (12) with the locking knob (5).

To switch off:

Press the on/off switch (12) briey and let go.

8.8. Einstellen der Drehzahl (Abb. 6)

Stellen Sie vor Beginn der Arbeit die Drehzahl pas-

send zur Anwendung ein. Verwenden Sie eine nied-

rige Drehzahl für grobe Schleifarbeiten, erhöhen Sie

die Drehzahl für Feinarbeiten.

Verstellen Sie die Drehzahl durch Drehen der Einstel-

lung Drehzahl (4).

Note: The insertion tool moves for a short while after

having it switched off. Do not put aside the power tool

until the insertion tool has come to a complete halt.

8.9. Grinding

1. Attach an appropriate abrasive sheet (17) and

select the corresponding speed.

2. Hold the power tool securely at the handle sur-

faces (3, 6, 8) and switch it on as described.

3. Wait until the insertion tool has reached its full

operating speed.

4. Hold the grinding plate (1) as parallel as possible

to the wall, and touch the surface to be processed

with the brush edge (A) rst.

5. Apply some pressure to the grinding head (1)

such that the insertion tool touches the surface

to be processed.

6. Constantly move the power tool over the surface.

Note: lf you want to avoid irregular grinding results, do

not keep the power tool at one spot for too long.

7. Lift the grinding plate (1) from the surface to be

processed before switching off the power tool.

8. Do not put aside the power tool until the insertion

tool has come to a complete halt.

8.10. After use

1. Switch off the power tool as described, discon-

nect it from the power supply and Iet it cool down.

2. Clean and maintain the power tool as described

under point 10, and store it carefully.

LED light (g. 7)

To ensure a well lit workplace, use the LED light (2) if

necessary.

Press the switch (D) to switch ON/OFF the LED light

(2).

Sanding a ceiling (Fig. 8)

When working on a ceiling area, secure the grinding

head with the spring (E). To do so, attach this to the

eyelet on the tool.

9. Electrical connection

The electrical motor installed is connected and

ready for operation. The connection complies

with the applicable VDE and DIN provisions. The

customer‘s mains connection as well as the ex-

tension cable used must also comply with these

regulations.

Damaged electrical connection cable

The insulation on electrical connection cables is often

damaged.

This may have the following causes:

• Passage points, where connection cables are

passed through windows or doors.

• Kinks where the connection cable has been improp-

erly fastened or routed.

• Places where the connection cables have been cut

due to being driven over.

• Insulation damage due to being ripped out of the

wall outlet.

• Cracks due to the insulation ageing.

Such damaged electrical connection cables must not

be used and are life-threatening due to the insulation

damage.

Check the electrical connection cables for damage

Bekijk gratis de handleiding van Scheppach DS940, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.