Scheppach AWH-500BL handleiding
Handleiding
Je bekijkt pagina 21 van 212
www.scheppach.com
GB
|
21
• Do not use this or any other product for welding un-
less you have been fully instructed in its use.
• Do not use the welding helmet if the protective panel
is cracked, if the protective panel or the sensors are
dirty or if the protective panel or the front holding
frame is loose.
• Keep the work area clean. A messy environment is
an invitation to injury.
• Observe the working space conditions. Do not use
a welding helmet in damp or wet places. Do not ex-
pose it to rain. Keep the work area well lit. Do not use
auto-darkening helmets in the vicinity of ammable
gases or liquids.
• Keep away from children and animals. Children
must never be in the work area. Do not allow them to
handle this helmet.
• Store devices that are not in use. When the welding
mask is not in use, it must be stored in a dry place.
Store the welding mask out of the reach of children.
• Dress appropriately. Do not wear loose clothing or
jewellery. Keep hair, clothing and gloves away from
moving parts. Protective devices are essential to
protect against welding jets, some examples are a
leather welding apron, welding sleeves, jeans with-
out cus, work boots. Wear a restrictive hair cover to
conceal long hair.
• Use eye and hearing protection. Wear approved
safety goggles under the welding helmet when
welding. Wear an approved protective mask and ear
defenders when welding.
• Always remain attentive. Observe what you are do-
ing and use your common sense. Do not weld when
you are tired.
• Check whether any parts are damaged. Before us-
ing a helmet, you should carefully inspect any parts
that appear damaged to ensure that they function
properly and full their intended function. Check that
moving parts, broken parts or mounting xtures,
and other conditions that may interfere with proper
operation are aligned and clamped. Damaged parts
should be properly repaired or replaced by a quali-
ed technician. Do not use the helmet if a switch is
not working properly.
• Replace parts and accessories. Only use identical
spare parts for maintenance work. The use of other
parts may render the helmet ineective, cause eye
damage and invalidate the warranty. Only use ac-
cessories that are intended for this welding mask.
Accessories are available from After Sales Support.
• Do not weld if you are under the in-
uence of alcohol or drugs.
Damage caused by non-observance or misuse is not
covered by the warranty and does not fall within the
manufacturer’s scope of liability. The device was de-
signed for domestic use and must not be used com-
mercially or industrially.
5. General safety instructions
m WARNING: Read all safety information and instruc-
tions. Failure to observe the warnings and instructions
may result in electric shock, re and/or serious injury.
If you follow these instructions, you will avoid any di-
culties that may arise during the installation and use of
this automatic welding shield. All technical data for the
welding helmet is also noted in the welding helmet it-
self. Please inform yourself about the technical facts of
this product rst. Read the instructions rst. This saves
considerable time and trouble during use and contains
important safety information.
Keep all warnings and instructions for future ref-
erence.
• The product is not suitable for laser welding.
• The product is not re resistant.
• Do not remove the ADF lter from the automatic
welding helmet and never open the housing of the
ADF lter without the manufacturer’s permission.
• Before each use, please check whether the welding
/ grinding setting has been selected correctly.
• The front panel must be installed on the outside of the
ADF lter. Otherwise the ADF lter may be damaged.
• Do not make any changes/replacements to the auto-
matic welding helmet and ADF lter without author-
isation.
• Please stop the work process immediately and con-
tact the dealer without delay if the lter does not
darken automatically during welding.
• Do not use alcohol, petrol or thinner to clean the
ADF lter. Do not place the ADF lter in water.
• The reaction time of the ADF liquid crystal becomes
slower when the ambient temperature is lower, but
the protective functions are not aected.
• This product cannot be used for overhead welding
and cutting work. If this product is used for overhead
welding or cutting, molten metal droplets can burn
through the ADF lter and cause injury to the user.
• Service life exceeded (insucient protection) -
Check the automatic welding helmet for damage and
service life before each use.
Bekijk gratis de handleiding van Scheppach AWH-500BL, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Scheppach |
| Model | AWH-500BL |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 28998 MB |
