Proline 66471 handleiding
Handleiding
Je bekijkt pagina 5 van 76
5
rightwards/leftwards.
PLEASE NOTE! The tool and accessories should be used (in
line with their manufacturer's instructions) solely for the
purposes they were designed for. It is strictly prohibited to
use the device for any other purposes.
Do not use the wrench as a hammer for removing or straightening the
cross connectors. Never try to adapt the tool to any other designation or
to modify it.
Every use of the tool incompliant with its above-mentioned designation
is prohibited and shall invalidate the warranty, leading to the absence of
any manufacturer's liability for the losses resulting therefrom.
Any modification of the device made by the user waive the
manufacturer's liability for damage and losses caused to the user and the
Noise and vibration data
environment.
The NOISE was measured in accordance with ISO 15744, ISO 4871.
To ensure use compliant with the designation, follow also the
Sound pressure level (LpA) of the tool loaded/without load is:
safety tips, installation instructions and operation guidelines in
the operation manual. Follow the applicable accident-
prevention regulations (OH&S) as strictly as possible.
The correct use of the pneumatic tool entails also maintenance, storage,
Sound power level (LwA) of the tool loaded/without load is:
transport and repairs.
The device may be repaired solely in the service workshops authorised by
the manufacturer. The tools supplied with compressed air should be
Measurement tolerance
repaired solely by authorised personnel.
PLEASE NOTE!Wear hearing protection!
Even given the use compliant with the designation, it is impossible to
The VIBRATION was measured in accordance with ISO 28927-2
rule out certain residual risk factors. Due to the tool structure and design,
The average vibration level when loaded is:
the following hazards may appear:
measurement tolerance
Hazard of injuries caused by detached parts.
measurement tolerance
Hearing impairment in the failure to use the required hearing
The measured vibration level is representative of the basic tool
protection.
applications. If the tool is used for any other applications or with other
The set includes
work tools, and if it is not maintained sufficiently, the vibration level may
deviate from the above.
INSTALLATION AND USE:
PLEASE NOTE! Before every use of the tool, ensure no
pneumatic system component is damaged. If you notice any
damage, replace the system components with new,
undamaged ones.
Before every use of the pneumatic system, remove the condensate inside
the tool, compressor and hoses.
Connecting the tool to the pneumatic system
Ensure air supply to the tool by means of the air pre-treatment unit and
air pressure measurement.
It is recommended to use an automatic lubricator in the line although
lubrication may be done manually before you start work and after every
hour of continuous device operation. To ensure the best results, lubricate
the device frequently but not excessively. The excess oil could accumulate
in the device and would be blown away with the outlet air.
Figure B on page 2 presents the recommended tool attachment method
to the pneumatic system.
System components:
Item 1: PLEASE NOTE! Read the operation manual before you switch on
the device!
Item Wear protective goggles!
Item Wear hearing protection!
Item Wear protective gloves!
-
-
n
źPneumatic impact wrench - 1 pc.
źWarranty - 1 pc.
źOperation manual - 1 pc.
n Device components
The device component numbers refer to the graphic presentation (fig. A) on
page 2 of the operation manual:
1. Air inlet
2. Air outlet
3. Air inlet connector*
n
4. Oilcan*
5. Pressure controller / Rotation direction switch
6. Drive 1/2"
7. Impact socket*
8. Handle
9. On/Off switch
* The described or presented accessory does not belong to the standard tool
equipment in whole.
1. Pneumatic tool
2. Air inlet connector
3. Quick-release coupling
4. Pressure hose
5. Lubricator
n
Model 66471 – 91,2/93,6 dB(A)
Model 66472 – 93,1/96,5 dB(A)
Model 66471 – 102,2/104,6 dB(A)
Model 66472 – 104,1/107,5 dB(A)
K /K =3dB(A).
pA wA
, EN 12096.
2 2
Model 66471 – 8,0 m/s ( K=1,29 m/s )
2 2
Model 66472 – 5,5 m/s ( K=1,04 m/s )
n Pictograms
The explanation of symbols on the device nameplate (see Fig. A1).
2:
3:
4:
TECHNICAL DATA:
0,63 MPa
515 Nm
11000 rpm
1/2"
3/8"(10 mm)
135 l/min
1,42 kg
Max. supply pressure
Torque
Working
Max
678 Nm
Rotational speed
Drive size
Supply inlet (air inlet)
1/4"(12,8mm)
Hose size
Required air flow (at 0.63 MPa)
144 l/min
Weight
MODEL
66471 66472
1084 Nm
9000 rpm
1,8 kg
1356 Nm
Bekijk gratis de handleiding van Proline 66471, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Proline |
| Model | 66471 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 16510 MB |
