Power Soak SKS-70 handleiding
Handleiding
Je bekijkt pagina 4 van 10
4 OM-SKEWER SOAK
TROUBLESHOOTING
DEFINITION OF RESPONSIBILITIES
Facility Owner/Manager
The troubleshooting that can be accomplished by people without technical training
is limited to reviewing the status lights, draining / filling the sink and operating the
appropriate control panel buttons. All other service procedures including opening
the control panel must be conducted by trained personnel. It is the responsibility
of the owner/manager to see that trouble shooting and service procedures are
conducted by people with the proper training.
ALL PROCEDURES RELATED TO OPENING THE CONTROL PANEL OR
SERVICING ELECTRICAL COMPONENTS MUST BE PERFORMED BY AN
AUTHORIZED SERVICE AGENCY. TO OBTAIN THE NAME OF A RECOMMENDED
SERVICE AGENT IN YOUR AREA, PLEASE CALL THE POWER SOAK SERVICE
DEPARTMENT AT 888-994-7636.
Service Agency
The Power Soak Skewer Washing machine contains high voltage components
that require the knowledge of a certified electrician. Do not attempt to service the
machine without proper training.
THE CONTROL PANEL, PUMP MOTOR AND HEATER (OPTIONAL) CONTAIN
HIGH VOLTAGE ELECTRICAL CONNECTIONS. DISCONNECT THE POWER TO
THE MACHINE AT THE MAIN CIRCUIT BREAKER BEFORE ATTEMPTING TO
SERVICE THE MACHINE.
PROPERLY INSTALL COVERS AND CLOSE THE CONTROL PANEL BEFORE
RECONNECTING THE POWER TO THE MACHINE.
CONTROL PANEL LIGHTS AND BUTTONS
Status Lights on Control Panel
The lights on the control panel will indicate the status for operation of the Skewer
Wash. The wash pump will be automatically stopped by several features of the control
system.
Green Light (under the green “Start” button)
Slow Flashing – “POWER ON” – Indicates the electrical system is energized and ready
to have the wash and sanitize sinks filled. The upper sensor does not sense a water
level high enough to start the machine.
Solid Illumination – “OPERATING” – Indicates that the wash sink is full and the START
button has been pressed. The UPM program will continue operating (solid illumination
of the green light) when the STOP button is pressed and the wash pump motor has
stopped. The green light will return to flashing when the wash tank is drained.
Blue Light (between the green “Start” and red “Stop” buttons)
The blue light is not used for normal operation. It is only used during service
procedures.
Red Light (under the red “Stop” button)
Slow Flashing – “FILL SANITIZER TANK” – When the wash tank is filled with water, the
red light will blink indicating the sanitizer tank must be filled to the water line. It will
turn off when the sanitizer tank is full.
Solid Illumination – “CHANGE SANITIZE SOLUTION” – Two hours after the tank is filled
to the top level sensor, the red light will illuminate indicating that it is time to change
the sanitizing solution.
CONTROL MODULE (UPM) LED LIGHTS
The Universal Programming Module (UPM) is mounted to the inside surface of the
control enclosure cover. This device has indicator lights to aid in troubleshooting. To
view this device the control panel cover must be opened by removing the two screws
at the top of the control panel face.
EXAMINATION OF THE UPM LIGHTS WILL REQUIRE THAT THE POWER IS
TURNED ON WHILE THE CONTROL PANEL DOOR IS OPEN. BE AWARE THAT
THE COMPONENTS INSIDE THE CONTROL PANEL OPERATE WITH HIGH
VOLTAGE AND MUST NOT BE TOUCHED WHILE THE POWER IS TURNED
ON. TOUCHING THE HIGH VOLTAGE CONNECTIONS WILL RESULT IN SEVER
ELECTRICAL SHOCK AND WILL CAUSE SERIOUS INJURY OR DEATH.
The UPM has six LEDs mounted on its top edge. The function of each LED is as
follows, starting from the right-most LED:
#1 - Power On*
#2 - Error Code
#3 - Wash Tank Low-level Sensor*
#4 - Wash Tank Upper-level Sensor*
#5 - Sanitizer Tank Low-level Sensor
#6 - Sanitizer Tank Upper-level Sensor
IMPORTANT
* Indicates lights that must be illumined for the wash pump to operate.
For an explanation of the sensor lights call the Power Soak service department
(
888-994-7636
), please note the “Error Code” (if any) that can be identified by
observing LED #2 on the UPM. If there is a control logic error, LED #2 will flash with
a “blinking” pattern. For example:
A “_” symbol represents a “long” flash
A “.” symbol represents a “short” flash
_ _ _ . => Water Level Problem
_ _ _ . . => Temperature Sensor Problem
_ _ _ . . . => Over-Current Problem
Please have this “Error Code” information available prior to calling Power Soak
Systems.
WASH PUMP WILL NOT OPERATE
Owner/Manager Check List
Review the control panel lights and complete the following procedures. If these
steps do not allow the machine to start, contact the Power Soak service department
(
888-994-7636
) or an authorized service company.
• No lights on the control panel:
o Power is turned off; check the main circuit breaker to see that it is turned on.
o Power supply is defective; call a service company to restore power to the
machine.
o Water temperature is above 135°F.
• Green light is flashing:
o Liquid level in the wash sink is below the top sensor; fill the wash sink to the
waterline.
o Liquid level sensor is dirty and does not detect the water level; clean the
liquid level sensors as described in the “Preventive Maintenance” section of
this manual. (The liquid level sensors are the white plastic disc with a metal
center located on the side walls of the wash and sanitizer sinks.)
Service Company Check List
The Owner/Manager Check List (above) must be verified. If there are no lights on
the control panel, check the following:
• Main power connection and wiring
• Fuse inside the control enclosure
• Bi-metallic disc switch for water temperature (switch must be closed if water
temperature is below 120°F)
• Bi-metallic disc switch for motor temperature (switch must be
closed if motor
temperature is below 150°F)
Bekijk gratis de handleiding van Power Soak SKS-70, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Power Soak |
| Model | SKS-70 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 3637 MB |
