Handleiding
Je bekijkt pagina 14 van 72
LED display
Shows the set temperature in °C or °F ("°F" no display for some models) and the Auto-
timer settings. While on DRY and FAN modes, it shows the room temperature.
Shows Error codes and protection code: E1-Room temperature sensor error. E2-
Evaporator temperature sensor error. E3-Condenser temperature sensor error. E4-
Display panel communication error. EC-Refrigerant leakage detection malfunction.
PI -Bottom tray is full--Connect the drain hose and drain the collected water away. lf
protection repeats, call for service.
Note: When one of the above malfunctions occurs, turn o the unit, and check for any
obstructions. Restart the unit, if the malfunction is still present, turn o the unit and
unplug the mains power cable. Contact the manufacturer or its service agents or a
similar qualified person for service.
Operation Instructions
COOL operation
• Press the "MODE" button until the "COOL" indicator light comes on.
• Press the ADJUST buttons"+" or"-" to select your desired room temperature. The temperature
can be set within a range of 17°C~30°C/ 62°F~86°F (or 88°F).
• Press the "FAN SPEED" button to choose the fan speed.
HEAT operation
• Press the "MODE" button until the "HEAT" indicator light comes on.
• Press the ADJUST buttons"+" or" -" to select your desired room temperature. The temperature
can be set within a range of 17°C~30°C/ 62°F~86°F (or 88°F).
• Press the "FAN SPEED" button to choose the fan speed.
DRY operation
• Press the "MODE" button until the "DRY" indicator light comes on.
• Under this mode, you cannot select a fan speed or adjust the temperature. The fan motor
operates at LOW speed.
• Keep windows and doors closed for the best dehumidifying eect.
• Do not put the duct to window.
AUTO operation
• When you set the air conditioner in AUTO mode, it will automatically select cooling, heating, or
fan only operation depending on what temperature you have selected and the room
temperature.
• The air conditioner will control room temperature automatically round the temperature point
set by you.
• Under AUTO mode, you cannot select the fan speed.
FAN operation
• Press the "MODE" button until the"FAN" indicator light comes on.
• Press the "FAN SPEED" button to choose the fan speed. The temperature cannot be adjusted.
• Do not put the duct to window.
TIMER operation
• When the unit is on, press the Timer button will initiate the Auto-o stop program, the TIMER
OFF indicator light illuminates. Press the UP or down button to select the desired time. Press
the TIMER button again within 5 seconds, the Auto-on start program is initiated. And the
TIMER ON indicator light illuminates. Press the up or down button to select the desired Auto-
on start time.
• When the unit is o, press the Timer button to initiate the Auto-on start program, press it
again within 5 seconds will initiate the Auto-o stop program.
• Press or hold the UP or DOWN button to change the Auto time by 0.5hour increments, up to 10
hours, then at 1 hour increments up to 24 hours. The control will count down the time
remaining until start.
• The system will automatically revert back to display the previous temperature setting if there
is no operation in a 5 seconds period.
• Turning the unit ON or OFF at any time or adjusting the timer setting to 0.0 will cancel the
Auto Start/Stop timer program.
SLEEP (ECO) operation
• Press this button, the selected temperature will increase (cooling) or decrease (heating) by
1°C/2°F (or 1°F) 30 minutes. The temperature will then increase (cooling) or decrease (heating)
by another 1 °C/ 2°F (or 1 °F) after an additional 30 minutes. This new temperature will be
maintained for 7 hours before it returns to the originally selected temperature. This ends the
Sleep/Eco mode and the unit will continue to operate as originally programmed.
NOTE: This feature is unavailable under FAN or DRY Mode.
Other features
FOLLOW ME/TEMP SENSING feature
NOTE: This feature can be activated from the remote control ONLY. The remote control serves as
a remote thermostat allowing for the precise temperature control at its location.
To activate the Follow Me/Temp Sensing feature, point the remote control towards the unit and
press the Follow Me/Temp Sensing button. The remote control will send this signal to the air
conditioner until press the Follow Me/Temp Sensing button again. If the unitdoes not receive the
Follow Me/Temp Sensing signal during any 7 minutes interval, the unit will exit the Follow
Me/Temp Sensing mode.
NOTE: This feature is unavailable under FAN or DRY mode.
AUTO-RESTART
If the unit breaks o unexpectedly due to the power cut, it will restart with the previous function
setting automatically when the power resumes.
AIR FLOW DIRECTION ADJUSTMENT
The louver can be adjusted automatically. Adjust the airflow direction automatically:
• When the Power is ON, the louver opens fully.
• Press the SWING button on the panel or remote controller to initiate the Auto swing feature.
The louver will swing up and down automatically.
• Do not adjust the louver manually.
WAIT 3 MINUTES BEFORE RESUMING OPERATION
After the unit has stopped, it cannot be restarted operation in the first 3 minutes. This is to
protect the unit. Operation will automatically start after 3 minutes.
POWER MANAGEMENT feature
Under cooling operation, when the ambient temperature is lower than the setting temperature
for a period of time, the unit will be automatically operated power management feature. The
compressor and fan motor stop. When the ambient temperature is higher than the setting
temperature, the unit will be automatically quit the power management feature. The
compressor and (or) fan motor run.
2726
GB
Bekijk gratis de handleiding van Point POAC8212, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Point |
| Model | POAC8212 |
| Categorie | Airco |
| Taal | Nederlands |
| Grootte | 9076 MB |
