Panduit FHSCT handleiding
Handleiding
Je bekijkt pagina 5 van 11
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2018
FS119A
5. POLISHING 900µm TIGHT-BUFFERED FIBER
Carefully read this entire section before proceeding.
5.1 Hold a piece of 5µm Aluminum Oxide polishing film in the air and
gently rub cleaved fiber stub against the film. Using a circular
motion, continue rubbing until the end of the fiber is even with
the end of the ferrule or adhesive bead. An indication of this is
when the stub no longer leaves white traces on the film.
Note: Make sure to hold film so that your fingers are supporting
the edges only and are not positioned directly behind fiber.
5.2 Thoroughly clean polishing puck and 85 durometer polishing
pad using an alcohol soaked wipe. Place a sheet of 1µm
diamond polishing film on the pad. Wet film by placing a quarter-
sized amount of distilled water in the center of the pad.
5.3 Carefully insert connector into the polishing puck until the
connector latches. Insure that the ferrule is protruding from the
hole in the underside of the puck. It may be necessary to unlatch
and reinsert the connector if the ferrule does not slide through
initially.
5.4 Place the puck in the center of the distilled water on the pad.
Keeping the puck flat against the film and pad, apply even
pressure and polish by making figure eight motions. Continue for
3-4 figure eights.
5.5 Turn the puck over and inspect for any remaining adhesive,
indicated by a dark color at the center of the ferrule. Repeat step
5.4 for 1-2 figure eights if adhesive is still present, then
reinspect.
5.6 Clean the ferrule tip and puck with an alcohol soaked lint-free
wipe. Clean the 1µm diamond polishing film using an alcohol
soaked wipe after every 5 connectors.
5.7 Inspect the fiber endface using a microscope. If scratches
remain, polish for an additional 1-2 figure eights on the 1µm
diamond film and reinspect.
WARNING: NEVER LOOK INTO THE END OF A FIBER
WHICH MAY HAVE A LASER COUPLED TO IT.
Note: Each time a mating takes place, clean the ferrule
endface thoroughly with an alcohol soaked lint-free wipe.
5.8 For singlemode only: Place a sheet of the .05µm lapping film
on the pad. Apply several drops of distilled water onto the center
of the film.
Page 5 of 11
3-4
WET
1µm
5.4
D
I
A
M
O
N
D
5.2
Polishing Puck with LC Adapter
Design prior to Design after July,
July, 2018 2018
POLISHING GUIDELINES
• Keep the puck flat against the polishing film.
• Figure eights should be about 3" tall and 1.5" wide.
• Always polish on a clean area of the 1µm diamond polishing film,
with figure eights traversing the film as shown in Figure 5.4.
• One sheet of 5µm (micron) polishing film will polish 2-4 ferrules.
• One sheet of 1µm diamond polishing film will polish 100 ferrules.
• One sheet of .05µm lapping film will polish approximately 18-20
ferrules.
• Clean the polishing puck and pad with a clean wipe moistened with
alcohol after each step.
• DO NOT OVERPOLISH.
5.1
5µm
Ferrule Tip After 1µm Diamond Polish
AB CD
A = Ideal. No blemishes on core or cladding.
B = Good. Cladding is chipped, but core is not.
C = Poor. Scratch across core. Try repolishing
or else reterminate.
D = Unacceptable. Fiber has shattered.
Reterminate.
5.5
Bekijk gratis de handleiding van Panduit FHSCT, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Panduit |
| Model | FHSCT |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 1872 MB |
