Handleiding
Je bekijkt pagina 67 van 191
67
English
Note
●
This function is effective when [PC input mode] is
[PC]. (see page 98)
●
This function may not operate depending on the video
output devices.
■ [Power save]
This function adjusts the brightness of the backlight to
reduce power consumption.
[Off]:
The power save function does not operate.
[On]:
Backlight brightness is reduced.
Note
●
When [Setup] - [Sensor settings] - [Ambient light
sensor] is set to an item other than [Off], [Power save]
cannot be set.
■ [Extended standby mode]
Sets the operation in standby mode by the “Power
management” function for the input terminal for which
the “Power management” function is set to [On].
[Mode 1]:
If a video signal (synchronized signal) is detected
at the input terminal with which the standby mode
is entered, the power is turned “ON” with the input.
[Mode 2]:
If a video signal (synchronized signal) is detected
at any of the input terminals for which the “Power
management” function is set to [On], the power
is turned “ON”, and the input is switched to the
detected input.
[Mode 3]:
Even when the power is turned off using the
remote control, if a video signal (synchronized
signal) is newly detected at any of the input
terminals for which the “Power management”
function is set to [On], the power is turned “ON”,
and the input is switched to the detected input.
Note
●
When this function is set to [Mode 3], set [Quick start]
to [On] to enable the operation.
●
When [Quick start] is set to [Off], this function works
as it is set to [Mode 2] even if it is set to [Mode 3].
●
This function does not operate if the power plug is
removed from the outlet. Turn the power “ON” once to
use this function.
■ [Changing delay]
Sets the delay time until the input is switched when
[Power management mode] is [Input detection].
[Off]:
Switches the input if a signal is interrupted even for
a very short period.
1 to 10:
Sets the delay time (sec.). Switches the input when
the set time has elapsed after detecting no signal
is present. However, if the detection period during
which no signal is present is shorter than the set
delay time, the input is not switched.
Note
●
The operation when [Input detection] is selected is the
same as the operation when [Input search] is set to
[Input detection]. (see page 60)
Audio input select
[Audio input select] - submenu screen
Audio input select
HDMI3 HDMI3
USB-C USB-C
PC AUDIO IN
HDMI1 HDMI1
HDMI2 HDMI2
SLOT SLOT
Screen Transfer
Screen Transfer
PC[YP
B
P
R
] AUDIO IN
Video input Audio input
HDMI1 HDMI1 / AUDIO IN / No audio
HDMI2 HDMI2 / AUDIO IN / No audio
HDMI3 HDMI3 / AUDIO IN / No audio
USB-C USB-C / AUDIO IN / No audio
SLOT SLOT / AUDIO IN / No audio
PC AUDIO IN / No audio
PC[YP
BPR] AUDIO IN / No audio
Screen Transfer
Screen Transfer / AUDIO IN /
No audio
●
No audio: No audio input (Mute)
When the setting for the audio input has been
changed from the factory settings, the audio input is
displayed as below.
HDMI1
Full
AUDIO IN
Bekijk gratis de handleiding van Panasonic TH-75SQ2HW, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Panasonic |
| Model | TH-75SQ2HW |
| Categorie | Monitor |
| Taal | Nederlands |
| Grootte | 26224 MB |
