Omnitronic VFM-215 AP MK2 handleiding
Handleiding
Je bekijkt pagina 24 van 32
24
•
EN
4
Setup
The speaker system can be placed as desired or mounted onto stands or distance tubes with a standard
tube diameter of 35 mm.
General notes
• The location must be solid, plane, anti-slip,
vibration-free, oscillation-free, and fire-resistant.
The installation area must hold a minimum point
load of 5 times the system's load (e.g. weight
20 kg - point load 100 kg). The speakers must
never be installed higher than 100 cm without
secondary attachment.
• Always install the speaker systems in a way that
a minimum distance of three meters to the
audience is kept. This is the only way to avoid
hearing damage for unreasonable listeners.
Block the area in front of the speaker systems
with appropriate means.
Stands and satellite systems
• It is possible to put the speaker system onto a
PA speaker stand via the dual flange on the
lower side or on top of a subwoofer system via a
distance tube. For this, insert a distance tube of
35 mm (accessory) into the flange on the upper
side of the subwoofer; then fasten the speaker
system on top.
• Stands must only be installed on a plane area
with a maximum inclination angle of 5°.
• When using stands or satellite systems under
the influence of horizontal forces, e.g. through
wind, the standing safety can be impaired. This
is why additional safety measures like attaching
ballast weights have to be taken.
• If inclined tension cables or prolonged outriggers
are used, the area of danger has to be marked
or even be blocked.
• Before lifting or lowering the telescopic tubes,
you must always block a safety area around the
stand or satellite system. This safety area must
have a diameter of 1.5 times the maximum
height.
• Lifted telescopic tubes always have to be
secured with a secondary securing!
• The total weight of the installation (=total weight
of all individual parts) must never exceed the
maximum load of the installation area.
• The speakers have to be installed out of the
reach of people. An unintended movement of
the load has to be avoided - also in case of fire!
• The installer is responsible for adhering to the
carrying capacity given by the manufacturer, the
safety requirements and the qualification of
possible co-workers.
• When people are located below the load, all
necessary safety measures have to be taken in
order to avoid injury.
• The personnel have to be instructed on the
content of the user manual and on the dangers
related with operating stands.
• Depending upon the individual installation spot,
all necessary measures against movement and
for securing the standing safety have to be
created.
• The installation is only allowed on carrying
areas. In some cases, an appropriate
substructure, e.g. via a balancing foot, has to be
created. When choosing the installation material,
optimum dimensions have to be chosen in order
to secure maximum safety.
• Speaker systems installed on stands or satellite
systems may cause severe injuries when
crashing! If installing on slippery surfaces, the
legs must be secured with screws or nails via
the provided holes or an anti-slippery mat has to
be used.
Making the Connections
To avoid interfering noise, switch off the speaker
system or set the output controls to minimum prior
to connecting and disconnecting equipment. Be
sure to use only high-grade cables.
• In the mono channels, feed the audio input
signal via XLR or 6.3 mm plug to the
MIC/LINE
jack. These inputs allow connecting audio units
with line level (e.g. mixer or CD player) or
dynamic microphones.
• The RCA and AUX input (model
208AP and
210AP) in the stereo channel is designed for
line
level. Use standard stereo RCA/jack cables to
connect a mixer, keyboard or another audio
device to this input.
• At the RCA output MIX OUT the master signal of
all signal sources is available. This output allows
connecting e.g. the input of another active
speaker system for additional PA applications.
• Finally, connect the supplied power supply cable
to the corresponding input and the mains plug to
an outlet.
Bekijk gratis de handleiding van Omnitronic VFM-215 AP MK2, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Omnitronic |
| Model | VFM-215 AP MK2 |
| Categorie | Speaker |
| Taal | Nederlands |
| Grootte | 5298 MB |
