MSW -TC-1100HA handleiding
Handleiding
Je bekijkt pagina 17 van 76
Rev. 01.07.2024
Rev. 01.07.2024
e) Lower the mounting arm until the mounting head
rests against the edge of the rim (if the arm is locked,
it must be unlocked rst using the locking lever (10)
for the MSW-TC-750 model or the button on the
handle (21) for the MSW – model TC-1100h).
f) Lock the mounting arm with the lever (10) for the
MSW-TC-750 model or the button on the handle (21)
for the MSW – model TC-1100h). The mounting head
will be locked in a vertical position. IMPORTANT:
Keep a distance of approx. 1-2 mm vertically and
approx. 3-5 mm horizontally between the mounting
head and the rim edge.
g) Position the tyre so that its bead passes over the
head (A) from the back of the mounting head and
under the head (B) from the front of the mounting
head.
A
B
i) Turn the table clockwise by pressing the pedal (3)
until the tyre is completely separated from the rim. If
the tyre removal process is stopped by an interlock
or slowed down by large resistance, stop the table
rotation (stop pressing the pedal 3) and temporarily
reverse the table rotation by releasing the pedal (3).
Release the interlock and continue removing the
tyre.
WARNING: Do not hold your hands under the wheel
when closing the turntable jaws.
Gripping the rim from the outside:
I. Press the pedal (2) and open the jaws.
II. Position the wheel on the jaws and press the pedal
(3) all the way down to tighten the rim. The jaws will
grip the wheel.
Gripping the rim from the inside:
I. Set the jaws in the closed position.
II. Position the wheel on the jaws and press the pedal
(2). The jaws will part and grip the wheel.
e) Make sure that the rim is securely clamped in the
jaws.
f) Lower the mounting arm until the mounting head
rests on the rim edge.
g) Lock the mounting arm using the lever (10).
IMPORTANT: Keep the distance of approx. 2 mm
between the mounting head and the rim edge.
WARNING: Do not put your hands on the wheel
when mounting it. When the mounting arm is being
moved to its working position, the user's hand can
be crushed between the rim and the mounting head.
WARNING: In order to avoid damage to the inner
tube (if there is one in the tyre), when the mounting
head and the tyre lever are being positioned, the
inner tube valve should be moved away by 10 cm to
the right of the mounting head.
h) Slide the tyre lever under the tyre bead. While
holding the lever against the recess in the mounting
head, tilt the protruding part of the lever towards the
rim.
WARNING: Keep your hands and other parts of the body
as far as possible from the mounting arm when the
table is turning.
j) Remove the tube if there is one in the tyre. Lift the
mounting arm by pulling the locking lever (10) to
facilitate removal of the inner tube.
k) The other side of the tyre should be peeled o in the
same way without changing the rim position.
Slide the tyre lever under the tyre bead. While
holding the lever against the recess in the mounting
head, tilt the protruding part of the lever towards the
rim.
l) Turn the table clockwise by pressing the pedal (3)
until the tyre is completely separated from the rim.
m) Pull the lever (10) to move the mounting arm
upwards, then remove the tyre.
3) Mounting the tyre
WARNING: An unsuitable tyre or a tyre in poor condition
can burst when inated. Before mounting the tyre, check
the following:
• The tyre and presure hose are not damaged.
A damaged tyre must never be mounted.
• The rim is without dents and is not bent. Special
attention should be paid to aluminum wheels,
which may be cracked on the inside and the defect
may not be visible to the naked eye. Rims that are
bent, dented or with hidden material defects can be
potentially dangerous when the tyre is being inated.
• The tyre and rim diameters are the same. Do not
mount tyres on rims unless it is clear without doubt
that the diameters are the same.
a) Lubricate the tyre beads with a suitable agent to
avoid damage and to facilitate assembly.
b) Place the rim in the center of the turntable, lightly
press the rim and press the pedal (2) so that the
clamping jaws will grip the rim.
c) Position the tyre on the rim so that the mounting
head can be placed against the rim.
d) (This step applies only to the model MSW-TC-
1100HA). Put the column in an upright position.
17
EN
Bekijk gratis de handleiding van MSW -TC-1100HA, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | MSW |
| Model | -TC-1100HA |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 13751 MB |
