MSW -TC-1100HA handleiding
Handleiding
Je bekijkt pagina 16 van 76
Rev. 01.07.2024
WARNING: Not lubricating the rim bead will cause serious
damage to the tyre.
f) Press the pedal (22), the column will be restored to
its initial position.
g) Press the locking button (21) in the holder and lower
the mounting arm until the mounting head rests
against the rim edge.
h) Lock the mounting arm with the button (21) on the
holder.
IMPORTANT: Keep a distance of approx. 1-2 mm
vertically and approx. 3-5 mm horizontally between
the mounting head and the rim edge.
WARNING: Do not put your hands on the wheel when
mounting it. When the mounting arm is being moved to its
working position, the user's hand can be crushed between
the rim and the mounting head.
WARNING: In order to avoid damage to the inner tube (if
there is one in the tyre), when the mounting head and the
tyre lever are being positioned, the inner tube valve should
be moved away by 10 cm to the right of the mounting
head.
i) Slide the tyre lever under the tyre bead. While
holding the tyre lever against the recess in the
mounting head, tilt the protruding part of the lever
towards the rim.
3-5mm
1-2mm
a
d) Ensure that the rim is securely clamped by the jaws.
e) Apply a proper slip enhancer to the tyre bead as
follows:
I. Place the pressure roller on the side of the tyre and
press the tyre lightly with it (push the switch (24)
forward to lower the roller position). This will bend
the bead away from the rim and lubricate the bead
and the rim edge with a suitable slip enhancer.
II. Turn the rotary table by pressing the pedal (3) and at
the same time lubricate with a brush soaked in the
slip enhancer.
WARNING: Keep your hands and other parts of the
body as far as possible from the mounting arm when
the table is turning.
k) Remove the tube (if any) from the tyre. To facilitate
this, tilt the column by pressing the pedal (22).
l) To facilitate removal of the second tyre bead from
the rim, you can use the circular roller.
I. Set the circular roller so that it touches the bottom
side of the tyre and half of the roller is under the tyre.
II. Use the switch (24) and pedal (3) to lift the tyre to the
upper edge of the rim.
m) Remove the other side of the tyre in the same way
without changing the position of the rim. Slide the
tyre lever under the tyre bead. While holding the
lever against the recess in the mounting head, tilt the
protruding part of the lever towards the rim.
n) Turn the table clockwise by pressing the pedal (3)
until the tyre is completely separated from the rim.
o) Tilt the column by pressing the pedal (22) and
remove the tyre.
MSW-TC-750a)
a) Unlock the position of the mounting arm by pulling
the lever (10) and raise the mounting arm.
b) Apply a proper slip enhancer to the tyre bead.
j) Turn the table clockwise by pressing the pedal (3)
until the tyre is completely separated from the rim. If
the tyre removal process is stopped by an interlock
or slowed down by large resistance, stop the table
rotation (stop pressing the pedal 3) and temporarily
reverse the table rotation by releasing the pedal (3).
Release the interlock and continue removing the
tyre.
WARNING: Not lubricating the rim bead will cause
serious damage to the tyre.
c) Position the wheel on the turntable jaws (in the case
of asymmetrical rims, the narrower part of the rim
should be up).
d) Tighten the wheel in the turntable jaws by pressing
the pedal (2). In order to properly grip the wheel with
the jaws, it must be positioned exactly in the middle
of the turntable.
16
EN
Bekijk gratis de handleiding van MSW -TC-1100HA, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | MSW |
| Model | -TC-1100HA |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 13751 MB |
