MSW -TC-1100HA handleiding
Handleiding
Je bekijkt pagina 15 van 76
Rev. 01.07.2024
Rev. 01.07.2024
d) Press the pedal (1) to start the separator.
The separator arm presses on the tyre and separates
it from the rim.
e) Release the pedal (1) so that the separator returns to
its initial position.
f) Turn the tyre a little and repeat the tyre peeling
process.
g) Repeat the above steps until the entyre tyre is
detached from the rim.
h) Turn the tyre to the other side and repeat the peeling
process.
2) Removing the tire
IMPORTANT: Before using the machine, deate the
tyre and remove all balance weights from the rim.
MSW-TC-1100HA
NOTE: When tilting the column, make sure that nobody is
behind the machine.
a) Press the pedal (22) to tilt the column.
b) Position the wheel on the turntable jaws (in the case
of asymmetrical rims, the narrower part of the rim
should be up).
c) Tighten the wheel in the turntable jaws by pressing
the pedal (2). In order to properly grip the wheel with
the jaws, it must be positioned exactly in the middle
of the turntable.
WARNING: Do not hold your hands under the wheel
while clamping the turntable jaws.
Gripping the rim from the outside:
I. Press the pedal (2) and open the jaws.
II. Position the wheel on the jaws and press the pedal
(3) all the way down to tighten the rim. The jaws will
grip the wheel.
Gripping the rim from the inside:
I. Set the jaws in the closed position.
II. Position the wheel on the jaws and press the pedal
(2). The jaws will part and grip the wheel.
If the machine is placed outside the building, it must be
roofed and adequately shielded from weather conditions.
ASSEMBLING THE APPLIANCE
MSW-TC-750
1. Pull the locking lever [10] of the mounting arm.
2. Extend the mounting arm [7] fully to the top.
3. Lock the position of the mounting arm [7] using the
locking lever [10].
4. Remove the protective tip [25] of the mounting arm
[7] using a suitable wrench.
5. Slide the spring onto the mounting arm [7].
6. Put the protective tip [25] on the upper part of
the arm [7] and secure the connection using the
appropriate wrench.
7. Mount the column [12] with the mounting arm [7]
on the machine body [26] using four bolts and nuts.
8. Mount the movement limiting knob [8] in the
horizontal part of the mounting arm [7].
9. Mount the separator arm [14] on the shank [B] found
on the side of the machine body [26].
10. Unscrew the nut from the piston rod [C] (in the
drawing it is obscured by the separator arm)
protruding from the side of the machine body [26].
11. Put the separator arm [14] on the piston rod [C] and
secure the connection with the nut.
12. Install the small spring [A] between the separator
arm [14] and the machine body [26].
13. Install the accessories / lubricant container [13] on
the right side of the machine body.
14. Insert the tyre lever into the hole behind the stopper
[16].
15. Attach the blow gun hose [11] to the top connection
of the compressed air unit of the machine [D].
16. Connect the compressed air supply line to the side
connection of the compressed air unit [D].
D
13
A
B
14
C
16
3.3. DEVICE USE
Machine operation is divided into four parts:
1) separating the tyre
2) removing the tyre
500mm500mm
500mm
900mm
3) mounting the tyre
4) pumping the tyre
IMPORTANT: Before using the machine, deate the
tyre and remove all balance weights from the rim.
1) Separating the tyre
IMPORTANT: Exercise caution when using the
separator. Anything within the range of the
separator's arm is vulnerable to crushing.
a) Deate the tyre before you start to separate it.
b) Fully close the turntable jaws by pressing the pedal
(2).
c) Lean the wheel against the stopper found on the
right side of the machine. Position the edge of the
separator blade along the tyre bead, approximately
1 cm from the rim.
15
EN
Bekijk gratis de handleiding van MSW -TC-1100HA, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | MSW |
| Model | -TC-1100HA |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 13751 MB |
