Mountfield SP555 handleiding
Handleiding
Je bekijkt pagina 19 van 24
19
Figure 9
30 mm
80 mm
Figure 10
oil filler cap/
dipstick
upper limit
lower limit
If the blade is damaged it should be replaced.
Replacement blades must always be marked with part number
81004144/0. If in doubt refer to your dealer, or telephone 0845 600 2912. Fit the new blade so that the stamped
logo is turned up facing the blade holder (not facing the grass).
adjuster
cable
Figure 11
ADJUSTING THE HEIGHT OF CUT
The height of cut adjustment not only determines the length of the cut grass, it also controls the airflow which car-
ries clippings into the collector. If the discharge chute becomes blocked, increase the airflow by raising the height
of cut. To prevent blockages when cutting long, thick grass, set the adjustment to the highest setting and cut the
grass; then cut it again on a lower setting.
To adjust the height of cut:
• stop the engine and disconnect the spark plug
• put the mower on a level surface
• Adjust the cutting height lever by pulling outwards and moving into
the required position (Figure 9)
• All four wheels must be at the same height.
Fill the fuel tank with unleaded petrol. Do not overfill; the level should
be below the bottom of the fuel tank neck.
BEFORE EACH USE
Always ensure that the mower is in a safe working condition.
Inspect the cutter blade for damage; check safety devices and
guards; check that all nuts, bolts and screws are secure.
Check the oil level as follows:
a) Remove the oil filler cap and wipe the dipstick clean (Figure 10)
b) Refit the dipstick into the filler neck without screwing it down.
Remove the dipstick and check the oil level; oil should be at the
FULL mark. The oil tank capacity is about 0,55 litre or 20 fluid oz.
c) If the oil level is low add Mountfield oil part number MX855 or a
SAE 10W-30 oil, to the upper limit on the dipstick. Do not overfill;
the oil level should not be above the FULL mark.
Stop the engine and disconnect the spark plug lead before working on the machine.
MAINTENANCE
DO NOT TIP THE MOWER ONTO ITS SIDE AS THIS WILL FLOOD THE AIR FILTER WITH OIL.
To access the underside of the machine, lift the front wheels by lowering the handle until it rests on the
ground.
CUTTER BLADE
Examine the cutter blade regularly for wear or damage.
A slightly worn blade can be re-sharpened by your local dealer
CLUTCH CABLE ADJUSTMENT (Self Propelled model only)
Make sure that the clutch lever is fully released.
Adjust the cable by screwing or unscrewing the cable adjuster
(figure 11). The cable should have about 12mm of play in it.
Engage the clutch lever and check that the rear wheels lock when
the mower is pulled backwards
Start the mower and ensure it does not drive when the lever is disen-
gaged.
ENGINE
An engine Manufacturer’s Owner’s Manual is supplied with your mower.
Please read this, it provides detailed information on engine operation, maintenance
and care. Repair work other than routine maintenance, should be carried out by an authorised dealer.
STORAGE
A little time spent on your mower after use will ensure many years of reliable mowing.
To access the underside of the cutter deck, ensure that spark plug lead is disconnected. Then lift the front wheels
by lowering the handle until it rests on the ground. Do not tip the mower onto its side, as this will flood the air filter
with oil.
Bekijk gratis de handleiding van Mountfield SP555, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Mountfield |
| Model | SP555 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 3412 MB |
