Handleiding
Je bekijkt pagina 8 van 24
8
XLR Connectors
Below is the pin conguration for the XLR bal-
anced output connectors on the DS200. Refer to the
diagram for connection:
PIN 1: Shield/Ground
PIN 2: + Input/Output
PIN 3: – Input/Output
Power Control Connector
The DS200 power control input receives an On/O sig-
nal from +5 to +12 volts. The power control output will in
turn provide a +12 volt output signal with a total current
up to 25mA. An additional connection is for controlling
the illumination of other McIntosh products’ meter power
output indicators. The 3.5mm stereo
mini phone plug connects to a McIntosh
preamplier or A/V control center power
control output.
Data Input and IR IN Port Connectors
The DS200 data in port receives remote control signals
from McIntosh preampliers and A/V control centers.
The data out port will send the converted IR com-
mands to another attached McIntosh
component. A 3.5mm stereo mini phone
plug is used for connection.
The IR in port also uses a 3.5mm stereo
mini phone plug and allows the con-
nection of other brand IR receivers to
the DS200.
Note: The IR receiver must provide its own
power supply.
The RS232-C Data Cable is a
3.5mm stereo mini phone plug
used to connect to external
third party controllers.
Power
Control
Meter
Illumination
Control
Ground
PIN 2 PIN 1
PIN 3
Data
Signal
N/C
Data
Ground
IR Data
Control
Ground
N/C
USB Audio
The USB audio input of the DS200 provides the
capability to receive music/sound in a digital format
from a connected computer.
Software Requirements
Apple
®
computers with OS-10.6.8 or later require
no additional driver install to communicate with the
DS200.
For Windows-based computers (PC), Windows 7
(Service Pack 1) or later is required. The correct
McIntosh USB audio driver must be installed for the
PC to communicate with the DS200.
To install the McIntosh USB driver for Windows-
based computers download the latest driver from the
McIntosh website: https://www.mcintoshlabs.com/
products/specialty-products/DS200
The driver can be found in the Downloads section
of the webpage under Software Updates. Choose the
McIntosh USB Audio Windows Driver. You may
select this driver in many third-party applications
such as JRiver Media Center.
The DS200’s display will show the sampling rate or
bit rate for the USB input.
Service USB Port
The service USB port on the rear of the DS200 is
for McIntosh service use only. Use the USB audio
port for audio input.
Optical
The two optical inputs allow digital sources to be
connected to the DS200 using TOSLINK cables
also known as “optical audio cables.” The optical
inputs can handle high resolution digital audio up
to 192kHz/24-bit. The DS200 DAC will process
standard format SPDIF PCM signals and Dolby
Digital and DTS bitstreams. Unsupported formats
can result in strange and/or unpleasant sounds.
Coax
The two digital coaxial inputs allow digital sources
to be connected to the DS200 using Digital Audio
RCA coaxial Cables. The coax inputs can handle
high-resolution digital audio up to 192kHz/24-bit.
The DS200 DAC will process standard format
SPDIF PCM signals and Dolby Digital and DTS
bitstreams. Remember, unsupported formats can
result in strange and/or unpleasant sounds.
DS200 TXD Out
Data being transmitted
DS200 RXD In
Data being received
Ground
Connectors and Cable Information
Bekijk gratis de handleiding van McIntosh DS200, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | McIntosh |
| Model | DS200 |
| Categorie | Speaker |
| Taal | Nederlands |
| Grootte | 4494 MB |