Handleiding
Je bekijkt pagina 11 van 24
11
DS200
System Menu Settings continued
Input Menu
Setting Options
COAX 1 On/Name/O
COAX 2 On/Name/O
OPTI 1 On/Name/O
OPTI 2 On/Name/O
USB On/Name/O
MCT On/Name/O
HDMI(ARC) On/Name/O
NETWORK On/Name/O
BLUETOOTH On/Name/O
The following changes can be made:
SETUP: Inputs
(Hold INPUT knob)
↓
SETUP: [ input name ]
[ On / Rename, Off ]
On / Rename: The selected input will be function-
ing as normal. Hold in the INPUT knob to enter the
menu to rename the input*.
O: The selected input will be deactivated and
will no longer be selectable from the main display
during normal use. Change this setting back to “On
/Rename” to make it selectable again.
*Renaming Inputs: While in the selected input’s
submenu, use the INPUT knob to navigate to the
input with the name you’d like to change (and turn
it On using the ADJUST knob if it isn’t already) so
that the display says “SETUP: [ input name ] On /
Rename” and hold the INPUT knob to begin renam-
ing. The character you are currently adjusting will
be blinking. Rotate the INPUT knob to select which
character you want to change and use the ADJUST
knob to change the character.
Output Level Adjust:
SETUP: LEVEL ADJUST
[ FIXED 100%, ADJUSTABLE ]
Select the xed setting for a system where the
DS200 DAC will feed a xed line-level signal into
a preamplier or integrated amp that has its own
master volume control under RS-232 control.
Select the adjustable setting when using the DS200
as both a DAC and a preamplier, to directly feed
a power amplier. In this case the DS200 ADJUST
knob will work as the system volume control, or
select the Fixed setting and choose the xed volume
output level, 100% to 0%.
RS232 Baud Rate Setup:
The settings for serial communications are:
8 bit, no parity and 1 stop bit
The speed at which the DS200 communicates with
devices plugged into the RS232 Port (the Baud Rate)
can be adjusted with this Setting.
SETUP: RS232
[ rate in bits ] Baud
It is recommended to leave this at the highest setting
of 115200.
Auto-O:
SETUP: Auto-Off
[ Enabled, Disabled ]
Enabled: The DS200 automatically enters Standby
Mode after approximately 30 minutes of not playing
sound or changing settings.
Disabled: The DS200 will not power o automati-
cally and will remain On until you turn it o.
Network Standby:
SETUP: Network Standby
[ Enabled, Disabled ]
Enabled: The network and Wi-Fi section will
remain powered even when the unit is in Standby
mode. This will allow the unit to be remotely
activated and turned On by your mobile device or
network connected device, like a PC.
Disabled: The Network and Wi-Fi section will
not be powered when the unit is in Standby mode,
preventing remote activation.
Max Output:
Use to select the output voltage at the analog out-
puts. 2.0V is recommended when feeding a pream-
plier input. A higher voltage can be selected when
feeding an amplier input.
Stream Control LEDs:
In Auto mode the LEDs above the left hand buttons
will turn on and o depending on the capabilities of
the streaming source. In ON mode the LED’s will
always be on.
Factory Reset:
Use the factory reset option if you wish to return
all settings to factory defaults. All previous setup
changes will be lost.
FACTORY RESET
(Hold INPUT knob)
While on this option, hold the INPUT knob until the
display says “In Progress!” and immediately release.
Once the display says “Completed!”, your unit’s set-
tings will be set back to their factory defaults.
Bekijk gratis de handleiding van McIntosh DS200, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | McIntosh |
| Model | DS200 |
| Categorie | Speaker |
| Taal | Nederlands |
| Grootte | 4494 MB |