Handleiding
Je bekijkt pagina 10 van 24
10
System Menu
The System Menu contains the following informa-
tion about the DS200.
Setting Options
DS200 V_._ _
S/N AKFxxxx
Version Number
Serial Number
WIRELESS Firmware
V_._ _
Version Number
BLUETOOTH Firmware
V_._ _
Version Number
Di1 FIRMWARE
V_._ _
Version Number
SETUP: Level Adjust
Setting %
Fixed/Adjustable
SETUP: Fixed Level
Setting %
100% - 0%
SETUP: R232
Baud Rate
115200, 57600,
38400, 19200, 9600
Baud
SETUP: Auto-O
Setting
Enabled/Disabled
Network Standby
Setting
Enabled/Disabled
SETUP: Max. Output 1.0, 1.5, 2.0, 2.5, 3.0,
4.0, 5.0, 6.0, 7.0, 8.0,
9.0 Volts RMS
Stream Ctrl LEDs Auto, Always On
FACTORY RESET
Note: Default settings are marked in bold.
Navigating the Setup Menus
Options:
• SETUP: System Menu
• SETUP: Input Menu
• SETUP: IR Menu
• SETUP: HDMI Menu
Entering Setup Menu:
To enter the Setup Menu, push and hold the INPUT
knob. Once the display shows the unit model, the
rmware version, and the serial number, release
the knob and you are in the setup menu. See next
section for the setup menu overview.
Note: “Enter Code” will appear if the INPUT knob is held
too long. This is for support purposes only. Press the
knob again to exit.
Selecting/Adjusting Menu Settings:
You can navigate through and select the dierent
options in the menus by rotating the INPUT knob.
To adjust a selected setting, use the ADJUST knob.
If a category in a menu has a submenu available,
the display will show “Hold Input”, allowing you
to hold down the INPUT knob to see additional
options.
Exiting/Navigating Back:
A brief deliberate press (not hold) and release of
the INPUT knob will exit the current menu. Make
additional presses until the display shows the main
operating screen to continue normal use of the unit.
System Menu Settings
The following is a list of the available settings
options. A down arrow ↓ represents being taken to
a submenu after holding the INPUT knob while the
display says “Hold Input”. The selectable options
will be listed in brackets [ ] and separated by com-
mas, with a brief description underneath of what
each option does when selected.
Serial Number:
The DS200’s unique serial number can be viewed
by entering the setup menu and rotating the INPUT
knob until you see “S/N:”. The numbers and letters
to the right are the unit’s serial number. This num-
ber can also be found on the rear of the unit.
Firmware Version:
Firmware is internal software that controls the
DS200’s functionality. Firmware upgrades when
available can be installed by qualied technicians.
The version of the main rmware of the DS200 can
be viewed by entering the setup menu. The rst set-
ting is called DS200. The number to the right is the
version number. For example, if the VFD displays
“DS200 V101”, then the main rmware is version
1.01.
There is also rmware for controlling the digital
audio hardware. To see the digital audio rmware
version, enter the setup menu and rotate the INPUT
knob until you see “Di1 FIRMWARE”. The number
following the V to the right is the digital audio
rmware version.
Bekijk gratis de handleiding van McIntosh DS200, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | McIntosh |
| Model | DS200 |
| Categorie | Speaker |
| Taal | Nederlands |
| Grootte | 4494 MB |