Maytag MTW5600RU handleiding
Handleiding
Je bekijkt pagina 3 van 8
3
WASHER MAINTENANCE AND
CARE
WATER INLET HOSES
Replace inlet hoses after 5 years of use to reduce the risk of hose
failure. Periodically inspect and replace inlet hoses if bulges,
kinks, cuts, wear, or leaks are found.
When replacing your inlet hoses:
■ Mark the date of replacement on the label with a permanent
marker.
■ Check that the old washers are not stuck on the appliance
inlet valves.
■ Use new washers in the new inlet hoses to ensure a proper
seal.
NOTE: Do not use old hoses. Property damage can result. This
appliance may not include inlet hoses. See online installation
instructions for more information.
WASHER CARE
Recommendations to Help Keep Your Washer Clean and
Performing at its Best:
1. Always use High Efciency (HE) detergents and follow the
HE detergent manufacturer’s instructions regarding the
amount of HE detergent to use. Do not use more than the
recommended amount because that may increase the rate
at which detergent and soil residue accumulate inside your
washer, which in turn may result in undesirable odor.
2. Use warm and hot wash water settings sometimes (not
exclusively cold water washes), because they do a better
job of controlling the rate at which soils and detergent
accumulate.
3. Always leave the washer lid/door open between uses to help
dry out the washer and avoid the buildup of odor-causing
residue.
FOR FRONT LOAD MODELS ONLY:
4. Periodically clean residue from all interior surfaces of the
window. For better care, wipe the entire inside of the door
with a damp cloth.
5. Always follow door seal maintenance instructions to clean
the door seal. Go online for complete instructions.
NON-USE AND VACATION CARE:
Operate your washer only when you are home. If moving,
or not using your washer for a period of time, follow these
steps:
1. Unplug or disconnect power to the washer.
2. Turn off the water supply to the washer, to avoid ooding
due to water pressure surge.
HELPFUL TIP: Attach a reminder note to the washer to turn
the water back on before washer’s next use.
3. Clean the Dispensers. Not all models are equipped with
dispensers. If your model has dispensers, refer to the
Cleaning Dispensers section online.
WINTER STORAGE CARE
IMPORTANT: To avoid damage, install and store washer where it
will not freeze. Because some water may stay in hoses, freezing
can damage the washer. If storing or moving during
freezing weather, winterize your washer.
To winterize washer:
1. Shut off both water faucets; disconnect and drain water inlet
hoses.
HELPFUL TIP: Attach a reminder note to the washer to turn
the water back on before washer’s next use.
2. Put 1 quart (1 L) of R.V. type antifreeze in basket and run
washer on Drain/Spin cycle for about 30 seconds to mix
antifreeze and remaining water.
3. Unplug washer or disconnect power.
TRANSPORTING YOUR WASHER
1. Shut off both water faucets. Disconnect and drain water
inlet hoses.
2. If washer will be moved during freezing weather, follow
“Winter Storage Care” directions before moving.
3. Disconnect drain hose from drain system and from back of
washer.
4. Unplug power cord.
5. Place inlet hoses and drain hose inside washer basket.
6. Bundle power cord with a rubber band or cable tie to keep it
from hanging to the ground.
FOR FRONT LOAD MODELS ONLY:
IMPORTANT: Call for service to install new transport bolts.
Do not reuse transport bolts. Washer must be transported
in the upright position. To avoid structural damage to your
washer, it must be properly set up for relocation by a certied
technician.
7. FOR TOP LOAD MODELS ONLY: Place packing tray from
original shipping materials back inside washer. If you do
not have packing tray, place heavy blankets or towels into
basket opening. Close lid and place tape over lid and down
front of washer. Keep lid taped until washer is placed in new
location. Transport washer in upright position.
REINSTALLING/USING WASHER AGAIN
To reinstall washer after non-use, vacation, winter storage, or
moving:
1. Refer to Installation Instructions online for more information
to locate, level, and connect the washer.
2. Before using again, run washer through the following
recommended procedure:
To use washer again:
1. Flush water pipes and hoses. Reconnect water inlet hoses.
Turn on both water faucets.
2. Plug into a grounded 3-prong outlet or reconnect power.
3. Run the washer through a full cycle (Clean Washer cycle
if preferred, if equipped) to clean washer and remove
antifreeze, if used. Use only HE (High Efciency) detergent.
Use 1/2 the manufacturer’s recommended amount for a
medium-size load.
Bekijk gratis de handleiding van Maytag MTW5600RU, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Maytag |
| Model | MTW5600RU |
| Categorie | Wasmachine |
| Taal | Nederlands |
| Grootte | 938 MB |
