Makita TM001G handleiding
Handleiding
Je bekijkt pagina 10 van 76
10 ENGLISH
CAUTION: Always install the battery cartridge
fully until the red indicator cannot be seen. If not,
itmayaccidentallyfalloutofthetool,causinginjuryto
youorsomeonearoundyou.
CAUTION: Do not install the battery cartridge
forcibly.Ifthecartridgedoesnotslideineasily,itis
notbeinginsertedcorrectly.
CAUTION: Always be sure that the tool is
switched o and the battery cartridge is removed
before carrying out any work on the tool.
Installing or removing application
tool
Optional accessory
WARNING: Do not install application tool
upside down. Installing application tool upside down
maydamagethetoolandcauseseriouspersonal
injury.
CAUTION: Clean up dust and perform lubri-
cation on the moving part of the lock lever from
time to time.Otherwisedustmayaccumulateinthe
moving part of the lock lever and hinder its smooth
movement.
CAUTION: Be careful when closing the lock
lever.
Hold the tool rmly when installing or removing
the application tool. Do not put your hand around
the original position of the lock lever. The lock
levermayclosesuddenlyandpinchyournger.
►Fig.6
NOTICE: Install application tool in the correct
direction according to your work.Applicationtool
canbeinstalledatanangleofevery30degree.
NOTICE: Do not start the tool while the lever
opens. Thetoolmaybedamaged.
1. Openthelockleverfullyuntilitsoundsaclick.
Removetheholderbolt.
Whenthelockleverisfullyopened,thepositionofthe
lockleverismaintainedevenifyoureleaseyourhand.
►Fig.7: 1. Lock lever 2.Holderbolt
2. Putanapplicationtool(optionalaccessory)onto
thetoolange.Andthen,inserttheholderboltuntilit
stops.
►Fig.8: 1.Holderbolt2.Applicationtool3. Tool
ange4.Applicationtool(sandingpad)
3. Return the lock lever to its original position.
Alwaysmakesurethattheapplicationtoolissecurely
held in place.
►Fig.9: 1. Lock lever
To remove the application tool, follow the installation
procedures in reverse.
CAUTION: When removing the application
tool, do not touch the application tool or the work-
piece immediately after operation; they may be
extremely hot and could burn your skin.
Using sanding application tool
Whenusingsandingapplicationtool,mounttheappli-
cation tool on the sanding pad so that it matches the
sanding pad direction.
Thesandingpadhasahookandlooptypettingsys-
temwhichallowseasyandrapidttingofasanding
paper.
Assandingpapershaveholesfordustextraction,
mount a sanding paper so that the holes in a sanding
paper match those in the sanding pad.
►Fig.10: 1. Sanding paper
Toremoveasandingpaper,raiseitsendandpeelito.
OPERATION
WARNING: Before starting the tool and
during operation, keep your hand and face away
from the application tool.
CAUTION: Do not apply excessive load to the
tool which may cause a motor lock and stop the
tool.
CAUTION: Do not operate the tool with press-
ing the battery cartridge against the tool.
NOTICE:Ifyouoperatethetoolwithforcingor
excessivepressure,theoverloadalertmayworkand
thentheamplitudeofvibrationincrease.
In this case, once isolate the application tool from
the workpiece, then the speed of the oscillation goes
back.Continueoperationwithanappropriateload.
Cutting, sawing and scraping
NOTICE: Do not move on the tool forcibly in the
direction (e.g. towards either side) of the appli-
cation tool with no cutting edge. It may damage
the tool.
NOTICE: Operate the tool with appropriate load.
Forcingorexcessivepressureonthetoolmayreduce
eciency.
Especiallywhenoperatingthetoolwithalongblade
(e.g.plungecutsawblade),applyingtoomuchpres-
surethatthebladebendsmaynotonlyreducee-
ciencybutalsoactivatetheprotectionsystem.
Puttheapplicationtoolontheworkpiece.
Andthenmovethetoolforwardsothattheapplication
tool movement does not slow down.
►Fig.11
Bekijk gratis de handleiding van Makita TM001G, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Makita |
| Model | TM001G |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 12012 MB |
