Makita TM001G handleiding

Handleiding

12345678910111213141516171819202122232425262728293031323334353637383940414243444546474849505152535455565758596061626364656667686970717273747576/ 76

Afdrukken

Je bekijkt pagina 9 van 76

9 ENGLISH

Overload protection

Whenthetool/batteryisoperatedinamannerthat

causesittodrawanabnormallyhighcurrent,thetool

stopsautomatically.Inthissituation,turnthetoolo󰀨

andstoptheapplicationthatcausedthetooltobecome

overloaded. Then turn the tool on to restart.

Overheat protection

Whenthetool/batteryisoverheated,thetoolstops

automatically.Inthissituation,letthetool/batterycool

beforeturningthetoolonagain.

Overdischarge protection

Whenthebatterycapacityisnotenough,thetoolstops

automatically.Inthiscase,removethebatteryfromthe

toolandchargethebattery.

Protection lock function

Whentheprotectionsystemworksrepeatedly,thetoolislocked.

In this situation, the tool does not start even if turning

thetoolo󰀨andon.Toreleasetheprotectionlock,

removethebattery,setittothebatterychargerandwait

untilthechargingnishes.

Protections against other causes

Protectionsystemisalsodesignedforothercauses

that could damage the tool and allows the tool to stop

automatically.Takeallthefollowingstepstoclearthe

causes,whenthetoolhasbeenbroughttoatemporary

halt or stop in operation.

1. Makesurethatallswitch(es)is/areintheo󰀨posi-

tion, and then turn the tool on again to restart.

2. Chargethebattery(ies)orreplaceit/themwith

rechargedbattery(ies).

3. Letthetoolandbattery(ies)cooldown.

Ifnoimprovementcanbefoundbyrestoringprotection

system,thencontactyourlocalMakitaServiceCenter.

Switch action

CAUTION: Before installing the battery car-

tridge into the tool, always check to see that the

tool is switched o󰀨.

Tostartthetool,slidetheslideswitchtowardthe“I

(ON)”position.

Tostopthetool,slidetheslideswitchtowardthe“O

(OFF)”position.

►Fig.2: 1. Slide switch

Adjusting the oscillation rate

Theoscillationrateisadjustable.Tochangetheoscilla-

tionrate,turnthedialbetween1and6.Thehigherthe

numberis,thehighertheoscillationrateis.Presetthe

dialtothenumbersuitableforyourworkpiece.

►Fig.3: 1. Dial

NOTE:Thedialcannotbeturneddirectlyfrom1to6

orfrom6to1.Forcingthedialmaydamagethetool.

Whenchangingthedialdirection,alwaysturnthedial

movingitthrougheachintermediatenumber.

Lighting up the front lamp

CAUTION: Do not look in the light or see the

source of light directly.

Slide the slide switch toward the "I (ON)" position to

light up the front lamp. The lamp keeps on lighting while

the switch is the "I (ON)" position.

The front lamp goes out 10 seconds after sliding switch

toward the "O (OFF)" position.

►Fig.4: 1. Front lamp

NOTE:Whentheoverheatprotectionortheprotec-

tionlockfunctionisworking,thefrontlampblinksfor

about1minutes.Referthesectionforthetool/bat-

teryprotectionsystem.

Electronic function

The tool is equipped with the electronic functions for

easyoperation.

Constant speed control

The speed control function provides the constant oscil-

lation rate regardless of load conditions.

Soft start feature

Soft start feature reduces starting reaction.

Accidental re-start preventive

function

Wheninstallingthebatterycartridgewhiletheslide

switch in the "I (ON)" position, the tool does not start.

Tostartthetool,rstslidetheslideswitchtowardthe

"O (OFF)" position and then slide it toward the "I (ON)"

position.

ASSEMBLY

Installing or removing battery

cartridge

CAUTION: Always switch o󰀨 the tool before

installing or removing of the battery cartridge.

CAUTION: Hold the tool and the battery car-

tridge rmly when installing or removing battery

cartridge.Failuretoholdthetoolandthebattery

cartridgermlymaycausethemtoslipo󰀨yourhands

andresultindamagetothetoolandbatterycartridge

andapersonalinjury.

Toinstallthebatterycartridge,alignthetongueonthe

batterycartridgewiththegrooveinthehousingandslip

itintoplace.Insertitallthewayuntilitlocksinplace

withalittleclick.Ifyoucanseetheredindicatoras

showninthegure,itisnotlockedcompletely.

Toremovethebatterycartridge,slideitfromthetool

whileslidingthebuttononthefrontofthecartridge.

►Fig.5: 1. Red indicator 2. Button 3.Batterycartridge

12345678910111213141516171819202122232425262728293031323334353637383940414243444546474849505152535455565758596061626364656667686970717273747576/ 76

Bekijk gratis de handleiding van Makita TM001G, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.

Productinformatie

Gerelateerde producten van Makita (Niet gecategoriseerd)

Handleiding bekijken

Makita 197235-3

Niet gecategoriseerd - handleiding

Handleiding bekijken

Makita CA5000

Niet gecategoriseerd - handleiding

Handleiding bekijken

Makita BL3622A

Niet gecategoriseerd - handleiding

Handleiding bekijken

Makita DBN601

Niet gecategoriseerd - handleiding

Handleiding bekijken

Makita DBN610

Niet gecategoriseerd - handleiding

Handleiding bekijken

Makita DHP490

Niet gecategoriseerd - handleiding

Handleiding bekijken

Makita DDF490

Niet gecategoriseerd - handleiding

Handleiding bekijken

Makita DFJ214

Niet gecategoriseerd - handleiding

Andere merken in Niet gecategoriseerd