Lofrans XP800 handleiding
Handleiding
Je bekijkt pagina 11 van 18
11
www.lofrans.com
Problem Possible causes Solution
1. The winch does not
work when a control
is operated.
1.1 Protection switch in OFF
position.
1.2 Lack of voltage in the system.
1.3 Failure of the control box.
1.4 Failure of the control panel.
1.5 Failure of the electric motor.
1.6 The gearmotor overheats and
the circuit breaker trips.
1.1 Check the protection switch and set it in the ON position.
1.2 Check the charge status of the battery, check connections.
1.3 Check and possibly replace the control box.
1.4 Check and possibly replace the control.
1.5 Measure the electric motor voltage; if it is OK, check the brushes
and clean them. If it does not work, replace the electric motor.
2. The chain jams
frequently.
2.1 The chain locker is not deep
enough with respect to the
quantity of chain chosen.
2.2 The chain is not suitable for
the gipsy.
2.3 The chain is not calibrated.
2.1 Position the anchor windlass in the deepest point of the chain
locker or reduce the quantity of chain.
2.2 Change the gypsy or the chain accordingly.
2.3 Check the chain: if it does not meet the tolerances,
it must be replaced.
3. The winch runs
slowly and at times
trips the circuit
breaker.
3.1 Section of cables not suitable.
3.2 Poor electrical connections.
3.3 Water leaks in the electric
motor or planetary gearbox.
3.4 The planetary gearbox lost
the lubrication grease.
3.5 The engine strains in one or
both directions.
3.6 The winch works only in one
direction.
3.7 The eloctrobrake does not
disengage properly.
3.1 Increase the cable section.
3.2 Check out the connections.
3.3 Replace the gear motor.
3.4 (SERVICE) Uninstall the gearbox and check out its condition.
Replace damaged parts after discovering the causes of the
leak. Also, replace gaskets and screws. Check out also the
engine condition, which may have been damaged during the
malfunction.
3.5 (SERVICE) Check out appropriately all connections of the power
cables. If they are alright, uninstall the engine (in some cases it
is convenient to disassemble also the gearbox). Check out and
possibly replace the brushes.
3.6 Check out on the control box that between B2-C and B3-C
contacts there are 12/24V when the respective buttons are
pressed. If this should happen and one of the relays does not
work, replace the control box.
3.7 Check the voltage of gear motor.
4. The gear motor runs
but the shaft does
not rotate either Up
or Down.
4.1 Heavy wear or damage of the
planetary gears.
4.2 Damage of the gear motor
shaft.
4.1 (SERVICE) Uninstall the winch and replace the planetary
gearbox. (*)
4.2 (SERVICE) Replace the gear motor. (*)
(*) Take advantage of this opportunity to replace any other worn
parts, especially seals, screws, circlips.
5. The clutch cone of
the windlass are
tightened but the
windlass cannot
hold the anchor.
5.1 The internal electrobrake is
malfunctioned
5.1 Remove the bottom plastic cover and inspect the internal cable
wiring in case there is no cable loose connection. Replace the
gear motor.
UK
7 TROUBLESHOOTING
LOFRANS'
Bekijk gratis de handleiding van Lofrans XP800, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Lofrans |
| Model | XP800 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 2438 MB |
