Livarno Lux IAN 354287 handleiding
Handleiding
Je bekijkt pagina 33 van 42
33 GB/MT
Initial use / Maintenance and cleaning
Remove the lampshade
2
from the light base
3
by turning the three levers
1
on the side of
the light outwards (see Fig. A and B).
Mark the drill holes using the holes in the light
base
3
intended for the screws
7
as a guide
(see Fig. C).
Now drill the mounting holes (approx. Ø 6 mm,
depth approx. 40 mm). Make sure that you do
not damage the power cable (see Fig. D).
Insert the wall plugs
6
into the drilled holes.
Secure the light base
3
using the included
screws
7
(see Fig. E). Feed the mains connec-
tion cable (external)
4
through the cable guide.
Remove the protective cover
5
from the lustre
terminal
8
by loosening the screw (see Fig. F).
Pull the protective tubes
9
over cables L and N
of the mains connection cable (external)
4
(see Fig. G).
Connect the mains connection cable (external)
4
with the light using the lustre terminal
8
.
Note: Make sure that you correctly connect
each individual wire of the mains connection
cable (external)
4
: live wire, black or brown =
symbol L, neutral wire, blue = symbol N. Connect
the protective conductor
(green-yellow) with
the earth terminal which is marked in the light
base
3
.
Screw the protective cover
5
of the lustre ter-
minal
8
tightly into place again (see Fig. G).
Place the lampshade
2
back onto the light
base
3
and close the three levers
1
(see
Fig. H).
Ensure that it is securely tightened.
Reinsert the fuse or switch the circuit breaker
back on (see Fig. I).
Your light is now ready to use.
Model 4144506L:
Before installing the light, remove the fuse or
switch off the circuit breaker (
0 setting) in the
fuse box.
Remove the lampshade
2
from the light base
3
by carefully turning it anticlockwise (see Fig. A
and B).
Mark the drill holes using the holes in the light
base
3
intended for the screws
7
as a guide
(see Fig. C).
Now drill the mounting holes (approx. Ø 6 mm,
depth approx. 40 mm). Make sure that you do
not damage the power cable (see Fig. D).
Insert the wall plugs
6
into the drilled holes.
Secure the light base
3
using the included
screws
7
(see Fig. E). Feed the mains connection
cable (external)
4
through the cable guide.
Remove the protective cover
5
from the lustre
terminal
8
by loosening the screw (see Fig. F).
Pull the protective tubes
9
over cables L and
N of the mains connection cable (external)
4
(see Fig. G).
Connect the mains connection cable (external)
4
with the light using the lustre terminal
8
.
Note: Make sure that you correctly connect
each individual wire of the mains connection
cable (external)
4
: live wire, black or brown =
symbol L, neutral wire, blue = symbol N. Connect
the protective conductor
(green-yellow) with
the earth terminal which is marked in the light
base
3
.
Screw the protective cover
5
of the lustre ter-
minal
8
tightly into place again (see Fig. G).
Secure the lampshade
2
, by screwing it clock-
wise onto the light base
3
(see Fig. H).
Reinsert the fuse or switch the circuit breaker
back on (see Fig. I).
Your light is now ready to use.
Maintenance and cleaning
RISK OF ELECTRIC SHOCK!
Disconnect the light from the mains circuit before
cleaning. To do so, remove the fuse or switch off
the circuit breaker in the fuse box (0 position).
RISK OF ELECTRIC SHOCK!
For electrical safety, never clean the light with water
or other liquids, or immerse it in water.
CAUTION! DANGER OF BURNS DUE
TO HOT SURFACES!
Allow the light to cool completely.
Safety / Preparation / Prior to installation / Initial use
Bekijk gratis de handleiding van Livarno Lux IAN 354287, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Livarno Lux |
| Model | IAN 354287 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 3790 MB |
