Lelit Anna PL41TEM handleiding
Handleiding
Je bekijkt pagina 12 van 56
Pagina 12
English
34. Before preparing your coffee, it is advisable to position the coffee/hot water/steam lever switch (13) on coffee
mode (down) and lift the pump lever switch (22) to dispense water for 5 seconds from the brewing group (5)
with the tightened filterholder (8) into the drip tray. After dispensing water for the indicated time, lower the
pump lever switch (22) in order to stop the purge.
35. Open the single packed pod and pay attention not to damage the pod.
36. Place the pod in its filter (18).
37. Insert the filterholder (8) in the brewing group (5), turn it from left to right with force, then put the cup on the
removable water drip tray (7).
38. Position the lever switch (13) on coffee and lift the pump switch (22). The pressure value on the manometer (17)
should reach the green zone during the extraction.
39. Once you get the desired quantity of coffee, push down the switch (22) again.
40. Remove the filterholder (8) and throw away the used pod.
Steam:
41. Check that the water tank (1) has been filled in with water by looking at the water level indicator (20).
42. Press the on/off switch (11): the indicator light of the switch (11) will come on. Do this operation only if the
machine is off. If it’s on, proceed to the next step.
43. Position the lever switch (13) on steam mode.
44. As soon as the light (14) goes on, the machine is ready for use.
45. Open the steam/hot water knob (4). First, a little water will come out followed by steam.
46. Put the cup with the desired infusion under the steam wand (6) and turn the knob (4) completely.
47. When the drink has been suitably frothed, close the steam/hot water knob (4).
48. IMPORTANT: after you have frothed your milk, reopen the steam/hot water knob (4) and position the steam
switch (13) on hot water, and lift up the pump switch (22). When the water flows out of the steam wand (6),
close the steam/hot water knob (4) again and at the same time push down the switch (22) and re-position the
switch (13) on coffee again. Clean carefully the steam/hot water wand (6) after each use. This operation is
needed in order to restore the water circuit inside the machine tubes.
Hot water:
49. Check that the water tank (1) has been filled in with water by looking at the water level indicator (20).
50. Press the on/off switch (11): the indicator light of the switch (11) will come on. Do this operation only if the
machine is off. If it’s on, proceed to the next step.
51. Position the lever switch (13) on hot water.
52. As soon as the PID display (21) shows the set temperature and the indicator light (14) remains on, the machine
is ready for use.
53. Before preparing your hot drinks, it is advisable to open the steam/hot water knob (4), turn the lever switch on
hot water (13) and lift the pump switch (22). Hot water coming is dispensed from the steam/hot water wand (6)
immediately. Dispense water into the drip tray for 5 seconds. After that lower the pump switch (22), then close
the steam/hot water knob (4).
54. Place an empty cup under the steam/hot water wand (6). Open the steam/hot water knob (4) and lift the pump
switch (22).
55. Hot water will flow out from the steam wand (6) immediately.
56. Once you have got the desired quantity of water, repress the switch (22) and close the steam/water knob (4).
57. After obtaining hot water from the wand (6), make sure that there is still water in the tank (1).
HOW TO SET THE BOILER TEMPERATURE BY MEANS OF THE PID:
The PID has been set by the producer of this machine on a temperature of 95°C. In order to change the temperature
please proceed as follows:
- press the button ; as soon as the display shows the writing “PRG” press the button ;
- as soon as the display shows the boiler’s temperature, help yourself with the buttons and in
order to set the desired temperature, starting from a min. of 80C° up to a max. of 130C°.
- after 3 sec. from pressing the last button, the inserted temperature is memorized, and the display shows the
set temperature.
NB: if the temperature is set too high, once a coffee request is made, the display starts to flash.
USEFUL TIPS:
- The single cup filter (9), the two-cup filter (10), the blind filter (12) and the pod filter (18) do not need to be
washed after each use but please check that the holes are not blocked.
- For best results, we suggest warming the cups up on the cup warmer (2) which works only when the machine
is on.
- The PID is already set by the producer on the right temperature for an excellent coffee. During heating and
coffee or water distribution, the temperature can oscillate (+/- 10/12°C). Also, a warning has been inserted:
after 108°C the PID’s display shows the temperature but intermittently; this is normal, and it warns the user
that the coffee will not be good if made with such high temperature.
CLEANING AND MAINTENANCE
Cleaning and maintenance of the machine are essential for the quality of the coffee and the durability of the
appliance.
Bekijk gratis de handleiding van Lelit Anna PL41TEM, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Lelit |
| Model | Anna PL41TEM |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 7729 MB |
Caratteristiche Prodotto
| Apparaatplaatsing | Ingebouwd |
| Soort bediening | Hefboom |
| Kleur van het product | Roestvrijstaal |
| Ingebouwd display | Ja |
| Gewicht | 7200 g |
