Lelit Anna PL41TEM handleiding
Handleiding
Je bekijkt pagina 11 van 56
Pagina 11
English
USER INSTRUCTIONS:
Starting of the machine:
1. Remove the machine from its packing and make sure all packing parts have been taken off (including the
protection bags).
2. Lay the machine on a flat and steady surface far away from hot places and from the water taps.
3. Remove the water tank cover (19) on the top of the machine and take out the water tank (1) paying attention
not to damage the water tubes inside the tank.
4. Rinse the water tank thoroughly with cold water.
5. Fill the tank (1) with cold water.
6. Replace the water tank (1) back in the machine and check that the water tubes are not bent and that the filter is
well set on one of them.
7. Place the filterholder (8) under the brewing group (5) and turn it from the left to the right. Leave it there so that
it can get warm and it gets ready for use.
8. Open the steam/hot water knob (4).
9. Place an empty jug under the steam/hot water wand (6). Position the coffee/hot water/steam lever switch (13)
on hot water mode (middle position) and lift the pump lever switch (22).
10. Plug in the machine in the mains. Make sure that the wall socket has the right voltage.
11. Turn the machine on by lifting the on /off switch (11). The integrated indicator light (11) turns on to confirm the
power supply.
12. When water is dispensed from the steam/hot water wand (6), lower the pump lever switch (22) and close the
steam/hot water knob (4).
13. Position the lever switch (13) on coffee mode (down), lift the pump lever switch (22) and deliver water from the
brewing group (5) for around 2 minutes with the filterholder inserted (8), after that stop the delivery by lowering
the pump lever switch (22). Wait at least 1 minute before proceeding with the next operation.
14. Fill the tank (1) with cold water.
15. Position the lever switch (13) on hot water mode (middle position), open the steam/hot water knob (4) and lift
the pump lever switch (22). Water is dispensed from the steam/hot water wand (6) immediately. Deliver water
for around 2 minutes from the steam/hot water wand (6); after that stop the delivery by lowering the coffee/hot
water extraction lever switch (22). Close the steam/hot water knob (4).
16. Wait at least 1 minute before proceeding with the next operation.
17. After completing all these operations, leave the machine on.
18. The PID (21) will visualize the degrees inside the boiler and will control the boiler’s heating.
19. The PID is already set from the producer on 95°C, i.e. the ideal temperature for a good cup of coffee. (If you
want to change the PID’s temperature, please follow the instructions written under How to set the
temperature inside the boiler by means of the PID).
Preparing a coffee:
20. Check that the water tank (1) has been filled in with water by looking at the water level indicator (20).
21. Press the on/off switch (11): the indicator light of the switch (11) will come on. Do this operation only if the
machine is off. If it’s on, proceed to the next step.
22. As soon as the PID’s display shows the set temperature and the indicator light (14) remains on, the machine is
ready for use.
23. Fit the single cup filter (9) or the two-cup filter (10) into the filterholder (8) that has been warmed up by leaving
it attached to the brewing group as described in point 7.
24. Before preparing your coffee, it is advisable to position the coffee/hot water/steam lever switch (13) on coffee
mode (down) and lift the pump lever switch (22) to dispense water for 5 seconds from the brewing group (5)
with the tightened filterholder (8) into the drip tray. After dispensing water for the indicated time, lower the
pump lever switch (22) in order to stop the purge.
25. Fill the filter with ground coffee by means of the supplied measure spoon (16): 1+ ½ measuring spoonful (16) =
1 coffee cup - 3 measuring spoonful (16) = 2 coffee cups. Every time you fill the filter with a spoonful of
coffee, press the coffee with the tamper (15) before proceeding to fill it with the next spoonful and make sure
that there are no coffee rests on the filter border.
26. Insert the filterholder (8) in the brewing group (5), turn it from left to right with force, then put the cup on the
removable water drip tray (7).
27. Position the lever switch (13) on coffee mode and lift up the pump switch (22). The pressure value on the
manometer (17) should reach the green zone during the extraction.
28. Once you get the desired quantity of coffee, push down the switch (22) again.
29. Remove the filterholder (8) and throw away the coffee grounds. Make sure that the filterholder is clean and
reposition it in the brewing group to warm up again.
Preparing a coffee with the use of coffee pods:
30. Check that the water tank (1) has been filled in with water by looking at the water level indicator (20).
31. Press the on/off switch (11): the indicator light of the switch (11) will come on. Do this operation only if the
machine is off. If it’s on, proceed to the next step.
32. As soon as the PID’s display shows the set temperature and the indicator light (14) remains on, the machine is
ready for use.
33. Fit the pod filter (18) into the filterholder (8) that has been warmed up by leaving it attached to the brewing
group as described in point 7.
Bekijk gratis de handleiding van Lelit Anna PL41TEM, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Lelit |
| Model | Anna PL41TEM |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 7729 MB |
Caratteristiche Prodotto
| Apparaatplaatsing | Ingebouwd |
| Soort bediening | Hefboom |
| Kleur van het product | Roestvrijstaal |
| Ingebouwd display | Ja |
| Gewicht | 7200 g |
