Lectrosonics SMV/941 handleiding
Handleiding
Je bekijkt pagina 9 van 24
Super-Minature Belt Pack Transmitter
Rio Rancho, NM
9
SMV/SMQV/X
• 100 Series mode: CP 100
• 200 Series mode: CP 200
• Mode 3 (contact the factory for details): CP 3
• 400 Series mode: CP 400
• IFB Series mode: CP IFB
• Mode 6 (contact the factory for details): CP 6
4) Press either AUDIO or FREQ button to select the
power setting screen and use the Up and Down
down arrows to select the desired level of power.
5) Simultaneously press the AUDIO and FREQ but-
tons to exit this mode and turn o the power.
Audio Screen
The Audio screen is used to
adjust input gain from 0 to +44
dB, and the low frequency
roll-o from 35 to 150 Hz.
Repeatedly pressing the AUDIO
button toggles back and forth
between the two displays. Press
and hold the AUDIO button and use the Up and Down
arrows to make adjustments.
Frequency Screen
The Frequency Screen
displays the operating fre-
quency in MHz or as a
two-digit hexadecimal num-
ber that corresponds
to the equivalent
Lectrosonics Frequency
Switch Setting. Repeatedly
pressing the FREQ button toggles between the two
displays. Press and hold the FREQ button and use the
Up and Down arrows to select the frequency.
Lock/Unlock Screen
Simultaneously pressing and
holding both the Up and
Down arrow buttons during
normal operation starts the
Lock timer. The timer starts at
three and counts down to
zero. When the timer reaches
zero, the transmitter’s controls are locked.
With the controls locked, the AUDIO and FREQ buttons
can still be used to display current settings. Any attempt
to change a setting by pressing either the Up or Down
arrow button will result in an on-screen Loc reminder that
the controls are locked. Remove the batteries to unlock
the control panel.
Important: Once the transmitter is locked, it
cannot be unlocked or powered o using the
buttons. The only ways to unlock a locked
transmitter are to remove the battery or unlock it
via the RM remote control.
Remote Control Operation
Remote Control Screens
The transmitters can be
congured to respond to
signals from the LectroRM
app or to ignore them. This
setting is accessed by holding
Down arrow button while
powering the transmitter on.
Use the arrow keys to toggle
between “rc on” (remote control on) and “rc oFF”
(remote control o). The default setting is “rc on.”
If a remote control signal is detected but the transmitter
is set to “rc oFF”, the message “rc oFF” will be displayed
briey on the transmitter’s LCD, to conrm that a valid
signal was received, but that the transmitter is not con-
gured to respond to it.
Remote functions available are:
• Tx Input Gain
• Sleep/Unsleep
• Lock/Unlock
• Frequency
• Tuning in 25 kHz steps
• Changing the low frequency roll-o setting
• Turning on/o the PWR and Audio LEDs
• Gain up/down functions
In sleep mode, the transmitter uses only 20% of the
normal amount of battery drain. Sleep mode can only be
invoked with the remote control, and can only be revoked
with the remote control or by removing the battery. When
in the sleep mode, the PWR LED blinks green every few
seconds to indicate that the transmitter is asleep and not
turned o.
NOTE: See LectroRM for more information.
Bekijk gratis de handleiding van Lectrosonics SMV/941, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Lectrosonics |
| Model | SMV/941 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 5751 MB |
