Lectrosonics SMV/941 handleiding
Handleiding
Je bekijkt pagina 8 van 24
SMV Series
LECTROSONICS, INC.
8
Operating Instructions
Power Up and Boot Sequence
1) Ensure that good batteries are installed in the unit.
2) Simultaneously press and hold the AUDIO and
FREQ buttons until the Power On Boot Sequence is
initiated.
The count will progress from 1
through 3 and the unit will
then power up with the RF
output turned on. During this turn on sequence, the
modulation and power LEDs all glow red, then
green, and then revert to normal operation.
The LCD displays a bootup sequence which con-
sists of four screens:
Company Name: Lectro
Frequency Block (bXX) and
Firmware Version (rX.X): b21r1.1 (typ)
Power Level Pr 250
Compatibility Mode: CP 400 (typ)
Audio: Aud 12 (typ)
Power Down
Initial Power O
Timer Screen
1) Simultaneously press and hold the AUDIO and
FREQ buttons while observing that the word “O”
appears in the LCD along with a counter.
2) When the counter reaches “0”, the unit turns o.
Note: If the AUDIO and FREQ buttons are
released before the LCD goes blank at the end
of the countdown, the unit will not turn off.
Instead, it will stay energized and the display will
return to the previous screen.
Standby Mode
Standby Screen
With the power turned o,
pressing the AUDIO and
FREQ buttons briey places
the unit in Standby Mode. In
this mode the RF output is
turned o so all setup adjustments can be made without
interfering with other systems operating in the same
location. The screen displays “rf OFF” to remind the user
that the unit is not transmitting.
While the unit is in the standby mode, access the setup
screens using the AUDIO and FREQ buttons and make
adjustments using the Up and Down arrows.
LCD Backlight Settings
The LCD backlight can be set to turn o after either 5
minutes or 30 seconds, or stay on continuously.
Hold the UP arrow in while powering up the unit to enter
the setup screen. Press the AUDIO button repeatedly
to step through the setup items to reach the backlight
settings screen. Use the UP or DOWN arrow button to
select the desired setting.
Selecting Step Size mode
Hold the UP arrow in while powering up the unit to enter
the setup screen. Press the AUDIO button repeatedly
to step through the setup items to reach the Step Size
Mode screen. Use the UP or DOWN arrow button to
select the desired setting.
Selecting the Compatibility Mode
and Output Power
Power setting
IFB compatibility mode
Compatibility Modes allow the
transmitter to work with a variety
of dierent receivers.
1) Set the receiver’s audio con-
trols to minimum.
2) From a power o condition,
hold down the Up arrow, then
simultaneously press the
AUDIO and FREQ buttons.
3) Press either AUDIO or FREQ button to select the
compatibility screen and use the Up and Down ar-
rows to select the desired mode.
SMV/SMQV
• Mode 3 (contact the factory for details): CP 3
• Nu Hybrid: CP Nu
• IFB Series mode: CP IFB
NOTE: If your Lectrosonics receiver does not
have Nu Hybrid mode, set the receiver to Euro
Digital Hybrid Wireless® (EU Dig. Hybrid).
SMV/SMQV-941, SMV/SMQV/E07-941
• Nu Hybrid: CP Nu
• IFB Series mode: CP IFB
Bekijk gratis de handleiding van Lectrosonics SMV/941, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Lectrosonics |
| Model | SMV/941 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 5751 MB |
