Lectrosonics SMV/941 handleiding
Handleiding
Je bekijkt pagina 10 van 24
SMV Series
LECTROSONICS, INC.
10
Set Up in 100 kHz Mode
The Frequency Screen
displays the operating fre-
quency in MHz or as a
two-digit hexadecimal num-
ber that corresponds to the
equivalent Lectrosonics
Frequency Switch Setting.
The example of the two-digit
display shown here indicates CH (channel) and 2C as the
frequency. Repeatedly pressing the FREQ button toggles
between the two displays. Press and hold the FREQ
button and use the Up and Down arrows to select the
frequency.
Set Up in 25 kHz Mode
The hexidecimal display in the 25 kHz mode will appear
with a decimal sux to indicate the 25 kHz steps.
471.800 MHz
472.025 MHz
472.650 MHz
473.175 MHz
Adjusting the Low Frequency Roll-o
Repeatedly press the AUDIO button until the LF roll-o
adjustment screen appears. Then press and hold the AU-
DIO button while selecting the desired roll-o frequency
with the UP and DOWN arrows.
The roll-o frequency can be set to 35, 50, 70, 100, 120
and 150 Hz.
Adjusting Audio Level (Gain)
The control panel Modulation LEDs indicate the audio
level and limiter activity. Once set, the transmitter’s audio
level setting should not be used to control the volume of
your sound system or recorder levels. This gain adjust-
ment matches the transmitter gain with the microphone’s
output level, the user’s voice level and the position of the
microphone. The audio input level (gain) is adjusted with
the unit in the Standby Mode or while powered up while
observing the LEDs.
It is desirable to to set the gain so that some limiting
occurs on louder peaks. The limiter is very transparent
and its eect is not audible until the system is close to
overload. In other words, don’t be shy about turning up
the gain.
Conguring for Power Restore
Power Restore Screens
When using external power
source through a battery
eliminator, Power Restore will
return your transmitter to
settings it had before it was
powered o. This eliminates
the need to power on through
the unit itself.
1) Press and hold the Down Arrow Button then power
on the transmitter by pressing the
Audio and Freq buttons simultaneously.
2) The LCD will display the status, either “rc ON” or
“rc OFF.” Press “AUDIO” or “FREQ” key to scroll
to the “PbAc setup screen
• PbAc 1 for power restore ON
• PbAc 0 for power restore OFF
3) When power restore is set to ON, the unit will turn
on whenever power is present at the battery termi-
nals until the power is manually turned o with the
control panel switches.
NOTE: The firmware “remembers” the power
status when a battery fails, so the transmitter
will be turned on automatically when the battery
is replaced and the previous settings will be
enabled. Power Up and Boot Sequence
Setting Transmitter Operating Frequency
Frequency displayed
in MHz
Frequency displayed as
two-digit hexadecimal
number
The frequency can be dis-
played either in MHz or as a
two-digit hexadecimal num-
ber and can be set in the
Standby Mode or when the
transmitter is powered up.
The hexadecimal numbering
system is unique to Lectro-
sonics where two alphanu-
meric characters correspond
to the left and right switch
settings on earlier analog
transmitters that had mechanical rotary switches to
adjust frequency.
1) Press the FREQ button to select either the MHZ
screen or the hexadecimal screen.
2) While holding the FREQ button, use the Up or
Down arrow buttons to move the operating fre-
quency up or down in 100 kHz increments from the
current setting.
Note: The operating frequency displayed on the
LCD wraps as it reaches the upper or lower end
of its range.
Most Lectrosonics receivers with an LCD interface indi-
cate the operating frequency both in MHz and as a two
digit hexadecimal number. In many cases, it is more con-
venient to use the two character hexadecimal numbers
rather than the six character frequency in MHz.
Bekijk gratis de handleiding van Lectrosonics SMV/941, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Lectrosonics |
| Model | SMV/941 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 5751 MB |
